diff --git a/config/default/Configuration.h b/config/default/Configuration.h
index c830bcc636..144f938027 100644
--- a/config/default/Configuration.h
+++ b/config/default/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
@@ -482,7 +504,7 @@
 
 // Resistor values when using MAX31865 sensors (-5) on TEMP_SENSOR_0 / 1
 //#define MAX31865_SENSOR_OHMS_0      100   // (Ω) Typically 100 or 1000 (PT100 or PT1000)
-//#define MAX31865_CALIBRATION_OHMS_0 430   // (Ω) Typically 430 for AdaFruit PT100; 4300 for AdaFruit PT1000
+//#define MAX31865_CALIBRATION_OHMS_0 430   // (Ω) Typically 430 for Adafruit PT100; 4300 for Adafruit PT1000
 //#define MAX31865_SENSOR_OHMS_1      100
 //#define MAX31865_CALIBRATION_OHMS_1 430
 
diff --git a/config/examples/3DFabXYZ/Migbot/Configuration.h b/config/examples/3DFabXYZ/Migbot/Configuration.h
index af069f0fd1..40cd3eee64 100644
--- a/config/examples/3DFabXYZ/Migbot/Configuration.h
+++ b/config/examples/3DFabXYZ/Migbot/Configuration.h
@@ -398,70 +398,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/ADIMLab/Gantry v1/Configuration.h b/config/examples/ADIMLab/Gantry v1/Configuration.h
index c14c9079ee..5e1f611340 100644
--- a/config/examples/ADIMLab/Gantry v1/Configuration.h	
+++ b/config/examples/ADIMLab/Gantry v1/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/ADIMLab/Gantry v2/Configuration.h b/config/examples/ADIMLab/Gantry v2/Configuration.h
index 955d605be2..668400fe0e 100644
--- a/config/examples/ADIMLab/Gantry v2/Configuration.h	
+++ b/config/examples/ADIMLab/Gantry v2/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/AlephObjects/TAZ4/Configuration.h b/config/examples/AlephObjects/TAZ4/Configuration.h
index 42552d4520..a4a4d55200 100644
--- a/config/examples/AlephObjects/TAZ4/Configuration.h
+++ b/config/examples/AlephObjects/TAZ4/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 7
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Alfawise/U20-bltouch/Configuration.h b/config/examples/Alfawise/U20-bltouch/Configuration.h
index 2fd1a56827..5f4a8df1e1 100644
--- a/config/examples/Alfawise/U20-bltouch/Configuration.h
+++ b/config/examples/Alfawise/U20-bltouch/Configuration.h
@@ -435,70 +435,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Alfawise/U20/Configuration.h b/config/examples/Alfawise/U20/Configuration.h
index 3e9fc6f09d..48bb64d840 100644
--- a/config/examples/Alfawise/U20/Configuration.h
+++ b/config/examples/Alfawise/U20/Configuration.h
@@ -435,70 +435,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/AliExpress/CL-260/Configuration.h b/config/examples/AliExpress/CL-260/Configuration.h
index b520be691a..4378283ad3 100644
--- a/config/examples/AliExpress/CL-260/Configuration.h
+++ b/config/examples/AliExpress/CL-260/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/AliExpress/UM2pExt/Configuration.h b/config/examples/AliExpress/UM2pExt/Configuration.h
index 67be1e0a1e..885117fc89 100644
--- a/config/examples/AliExpress/UM2pExt/Configuration.h
+++ b/config/examples/AliExpress/UM2pExt/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 20
 #define TEMP_SENSOR_1 20
diff --git a/config/examples/Anet/A2/Configuration.h b/config/examples/Anet/A2/Configuration.h
index acdcb52fea..bfbb827dc8 100644
--- a/config/examples/Anet/A2/Configuration.h
+++ b/config/examples/Anet/A2/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Anet/A2plus/Configuration.h b/config/examples/Anet/A2plus/Configuration.h
index cc60567d5d..29a07e6aa5 100644
--- a/config/examples/Anet/A2plus/Configuration.h
+++ b/config/examples/Anet/A2plus/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Anet/A6/Configuration.h b/config/examples/Anet/A6/Configuration.h
index 860e959afd..ec8a10869a 100644
--- a/config/examples/Anet/A6/Configuration.h
+++ b/config/examples/Anet/A6/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 11
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Anet/A8/Configuration.h b/config/examples/Anet/A8/Configuration.h
index cbe9c28a85..c2cdc68735 100644
--- a/config/examples/Anet/A8/Configuration.h
+++ b/config/examples/Anet/A8/Configuration.h
@@ -398,70 +398,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Anet/A8plus/Configuration.h b/config/examples/Anet/A8plus/Configuration.h
index a90e10f07b..1e8a540f34 100644
--- a/config/examples/Anet/A8plus/Configuration.h
+++ b/config/examples/Anet/A8plus/Configuration.h
@@ -398,70 +398,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Anet/A9/Configuration.h b/config/examples/Anet/A9/Configuration.h
index d16aef4a97..ccb2fbb012 100644
--- a/config/examples/Anet/A9/Configuration.h
+++ b/config/examples/Anet/A9/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Anet/E10/Configuration.h b/config/examples/Anet/E10/Configuration.h
index 3302139e85..4351663be6 100644
--- a/config/examples/Anet/E10/Configuration.h
+++ b/config/examples/Anet/E10/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Anet/E16/BTT SKR 1.3/Configuration.h b/config/examples/Anet/E16/BTT SKR 1.3/Configuration.h
index 04919defe1..f8236e17a6 100644
--- a/config/examples/Anet/E16/BTT SKR 1.3/Configuration.h	
+++ b/config/examples/Anet/E16/BTT SKR 1.3/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Anet/E16/Stock/Configuration.h b/config/examples/Anet/E16/Stock/Configuration.h
index 92bb91d0db..e81f2c2b88 100644
--- a/config/examples/Anet/E16/Stock/Configuration.h
+++ b/config/examples/Anet/E16/Stock/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Anet/ET4+/Configuration.h b/config/examples/Anet/ET4+/Configuration.h
index 53012ab84a..bdc4c2e848 100644
--- a/config/examples/Anet/ET4+/Configuration.h
+++ b/config/examples/Anet/ET4+/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Anet/ET4-Pro/Configuration.h b/config/examples/Anet/ET4-Pro/Configuration.h
index 7ebf1192cd..0c018ffff7 100644
--- a/config/examples/Anet/ET4-Pro/Configuration.h
+++ b/config/examples/Anet/ET4-Pro/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Anet/ET4/Configuration.h b/config/examples/Anet/ET4/Configuration.h
index 60a6d5ba09..d3219ed92f 100644
--- a/config/examples/Anet/ET4/Configuration.h
+++ b/config/examples/Anet/ET4/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Anet/ET4X/Configuration.h b/config/examples/Anet/ET4X/Configuration.h
index b05ad61513..9414ecd4c0 100644
--- a/config/examples/Anet/ET4X/Configuration.h
+++ b/config/examples/Anet/ET4X/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Anet/ET5-Pro/Configuration.h b/config/examples/Anet/ET5-Pro/Configuration.h
index a86a3002b9..129f53d3f3 100644
--- a/config/examples/Anet/ET5-Pro/Configuration.h
+++ b/config/examples/Anet/ET5-Pro/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Anet/ET5/Configuration.h b/config/examples/Anet/ET5/Configuration.h
index 00bc9f1b54..f48fd1c61b 100644
--- a/config/examples/Anet/ET5/Configuration.h
+++ b/config/examples/Anet/ET5/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Anet/ET5X/Configuration.h b/config/examples/Anet/ET5X/Configuration.h
index f896c48db1..0ce6cd9dcd 100644
--- a/config/examples/Anet/ET5X/Configuration.h
+++ b/config/examples/Anet/ET5X/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/AnyCubic/Chiron/Configuration.h b/config/examples/AnyCubic/Chiron/Configuration.h
index b1a775f68c..3581ce40b6 100644
--- a/config/examples/AnyCubic/Chiron/Configuration.h
+++ b/config/examples/AnyCubic/Chiron/Configuration.h
@@ -400,70 +400,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration.h b/config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration.h
index 1534ca4c7c..6e374ea0bb 100644
--- a/config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration.h	
+++ b/config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration.h	
@@ -398,70 +398,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h b/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h
index 999e73ed48..f10f665b6b 100644
--- a/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h	
+++ b/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration.h	
@@ -398,70 +398,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h b/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h
index 2f9a833bad..63699a3be6 100644
--- a/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h	
+++ b/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/AnyCubic/i3 Mega/Configuration.h b/config/examples/AnyCubic/i3 Mega/Configuration.h
index 838ac00a09..a1d9b77957 100644
--- a/config/examples/AnyCubic/i3 Mega/Configuration.h	
+++ b/config/examples/AnyCubic/i3 Mega/Configuration.h	
@@ -418,70 +418,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/AnyCubic/i3/Configuration.h b/config/examples/AnyCubic/i3/Configuration.h
index b975b31016..78e50e95a3 100644
--- a/config/examples/AnyCubic/i3/Configuration.h
+++ b/config/examples/AnyCubic/i3/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/ArmEd/Configuration.h b/config/examples/ArmEd/Configuration.h
index be33ecec63..b025c21879 100644
--- a/config/examples/ArmEd/Configuration.h
+++ b/config/examples/ArmEd/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Artillery/Genius/Configuration.h b/config/examples/Artillery/Genius/Configuration.h
index d9e7d4b822..bc02c6791c 100644
--- a/config/examples/Artillery/Genius/Configuration.h
+++ b/config/examples/Artillery/Genius/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Artillery/Sidewinder X1/Configuration.h b/config/examples/Artillery/Sidewinder X1/Configuration.h
index 2d4f370b09..e98f5efcee 100644
--- a/config/examples/Artillery/Sidewinder X1/Configuration.h	
+++ b/config/examples/Artillery/Sidewinder X1/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Artillery/Sidewinder X1_0.9_degree_BMG_E3D_V6/Configuration.h b/config/examples/Artillery/Sidewinder X1_0.9_degree_BMG_E3D_V6/Configuration.h
index cbb33a6623..37ac512302 100644
--- a/config/examples/Artillery/Sidewinder X1_0.9_degree_BMG_E3D_V6/Configuration.h	
+++ b/config/examples/Artillery/Sidewinder X1_0.9_degree_BMG_E3D_V6/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Azteeg/X5GT/Configuration.h b/config/examples/Azteeg/X5GT/Configuration.h
index e9099276a7..c820030911 100644
--- a/config/examples/Azteeg/X5GT/Configuration.h
+++ b/config/examples/Azteeg/X5GT/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 1
diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration.h b/config/examples/BIBO/TouchX/cyclops/Configuration.h
index 600cd539c0..b8a4d930ac 100644
--- a/config/examples/BIBO/TouchX/cyclops/Configuration.h
+++ b/config/examples/BIBO/TouchX/cyclops/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/BIBO/TouchX/default/Configuration.h b/config/examples/BIBO/TouchX/default/Configuration.h
index 26453cab3b..55a184b0d8 100644
--- a/config/examples/BIBO/TouchX/default/Configuration.h
+++ b/config/examples/BIBO/TouchX/default/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 5
diff --git a/config/examples/BIQU/B1-BLTouch/Configuration.h b/config/examples/BIQU/B1-BLTouch/Configuration.h
index 533ad2008d..5b7c978928 100644
--- a/config/examples/BIQU/B1-BLTouch/Configuration.h
+++ b/config/examples/BIQU/B1-BLTouch/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/BIQU/B1/Configuration.h b/config/examples/BIQU/B1/Configuration.h
index a6d40231a1..98bcb4e041 100644
--- a/config/examples/BIQU/B1/Configuration.h
+++ b/config/examples/BIQU/B1/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/BQ/Hephestos/Configuration.h b/config/examples/BQ/Hephestos/Configuration.h
index 5bcebb53ea..6103b18e51 100644
--- a/config/examples/BQ/Hephestos/Configuration.h
+++ b/config/examples/BQ/Hephestos/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/BQ/Hephestos_2/Configuration.h b/config/examples/BQ/Hephestos_2/Configuration.h
index 49b575affb..b0855ec288 100644
--- a/config/examples/BQ/Hephestos_2/Configuration.h
+++ b/config/examples/BQ/Hephestos_2/Configuration.h
@@ -405,70 +405,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 70
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/BQ/WITBOX/Configuration.h b/config/examples/BQ/WITBOX/Configuration.h
index b47c23c67d..ab1b63be51 100644
--- a/config/examples/BQ/WITBOX/Configuration.h
+++ b/config/examples/BQ/WITBOX/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/CTC/A13/Configuration.h b/config/examples/CTC/A13/Configuration.h
index e0ec524bb6..87f9f9fc99 100644
--- a/config/examples/CTC/A13/Configuration.h
+++ b/config/examples/CTC/A13/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h b/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h
index c0e5bc5abd..19033f1ac9 100644
--- a/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h	
+++ b/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Cartesio/Configuration.h b/config/examples/Cartesio/Configuration.h
index 942f740d89..295318428e 100644
--- a/config/examples/Cartesio/Configuration.h
+++ b/config/examples/Cartesio/Configuration.h
@@ -398,70 +398,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 -1
 #define TEMP_SENSOR_1 -1
diff --git a/config/examples/Copymaster3D/300/Configuration.h b/config/examples/Copymaster3D/300/Configuration.h
index 2505876924..af7afb9b6b 100644
--- a/config/examples/Copymaster3D/300/Configuration.h
+++ b/config/examples/Copymaster3D/300/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 202
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Copymaster3D/400/Configuration.h b/config/examples/Copymaster3D/400/Configuration.h
index d6f7f02264..d34f0eb6fd 100644
--- a/config/examples/Copymaster3D/400/Configuration.h
+++ b/config/examples/Copymaster3D/400/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 202
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Copymaster3D/500/Configuration.h b/config/examples/Copymaster3D/500/Configuration.h
index a54d25fd38..3380428164 100644
--- a/config/examples/Copymaster3D/500/Configuration.h
+++ b/config/examples/Copymaster3D/500/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 202
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration.h
index da4bd21b4f..444da8c94e 100644
--- a/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration.h	
+++ b/config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration.h	
@@ -406,70 +406,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h b/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h
index c3e9ceafca..0ddc202e52 100644
--- a/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h	
+++ b/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration.h	
@@ -406,70 +406,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h b/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h
index 3bacb31966..6fddefd81f 100644
--- a/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h	
+++ b/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h b/config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h
index ede77a8b12..4200cc6ba9 100644
--- a/config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h	
+++ b/config/examples/Creality/CR-10 S4/CrealityV1/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h b/config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h
index 7bcc710fcd..08f1a396d7 100644
--- a/config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h	
+++ b/config/examples/Creality/CR-10 S5/CrealityV1/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/CR-10 V2/Configuration.h b/config/examples/Creality/CR-10 V2/Configuration.h
index 5b11b1f0f6..1d72d41914 100644
--- a/config/examples/Creality/CR-10 V2/Configuration.h	
+++ b/config/examples/Creality/CR-10 V2/Configuration.h	
@@ -404,70 +404,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/CR-10 V3/Configuration.h b/config/examples/Creality/CR-10 V3/Configuration.h
index 92aeff500e..0d17bf4286 100644
--- a/config/examples/Creality/CR-10 V3/Configuration.h	
+++ b/config/examples/Creality/CR-10 V3/Configuration.h	
@@ -404,70 +404,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h
index 12b9e26457..726a3fac6d 100644
--- a/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h	
+++ b/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/CR-10/CrealityV1/Configuration.h b/config/examples/Creality/CR-10/CrealityV1/Configuration.h
index 162d800005..d01fa203fc 100644
--- a/config/examples/Creality/CR-10/CrealityV1/Configuration.h
+++ b/config/examples/Creality/CR-10/CrealityV1/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration.h b/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration.h
index 0c12de8085..dd52c9178b 100644
--- a/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration.h	
+++ b/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h
index 6e27044ff5..efda9f7fcc 100644
--- a/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h	
+++ b/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration.h b/config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration.h
index 34b593d22c..f1c7dbe793 100644
--- a/config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration.h	
+++ b/config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/CR-10S/CrealityV1/Configuration.h b/config/examples/Creality/CR-10S/CrealityV1/Configuration.h
index a334b3483a..c425934608 100644
--- a/config/examples/Creality/CR-10S/CrealityV1/Configuration.h
+++ b/config/examples/Creality/CR-10S/CrealityV1/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/CR-20 Pro/Configuration.h b/config/examples/Creality/CR-20 Pro/Configuration.h
index 1be1fed45d..c9318602a0 100644
--- a/config/examples/Creality/CR-20 Pro/Configuration.h	
+++ b/config/examples/Creality/CR-20 Pro/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/CR-20/Configuration.h b/config/examples/Creality/CR-20/Configuration.h
index c6fb30ddcf..d67aeb9fd2 100644
--- a/config/examples/Creality/CR-20/Configuration.h
+++ b/config/examples/Creality/CR-20/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/CR-6 SE/Configuration.h b/config/examples/Creality/CR-6 SE/Configuration.h
index 18f6da4807..f0fb1c320e 100644
--- a/config/examples/Creality/CR-6 SE/Configuration.h	
+++ b/config/examples/Creality/CR-6 SE/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/CR-8/Configuration.h b/config/examples/Creality/CR-8/Configuration.h
index 550552940e..bcd0db83df 100644
--- a/config/examples/Creality/CR-8/Configuration.h
+++ b/config/examples/Creality/CR-8/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-2/Configuration.h b/config/examples/Creality/Ender-2/Configuration.h
index 280aac4cf5..71f24b9b22 100644
--- a/config/examples/Creality/Ender-2/Configuration.h
+++ b/config/examples/Creality/Ender-2/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-3 Max/Configuration.h b/config/examples/Creality/Ender-3 Max/Configuration.h
index 2e95825e57..9bae4a60e7 100644
--- a/config/examples/Creality/Ender-3 Max/Configuration.h	
+++ b/config/examples/Creality/Ender-3 Max/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration.h
index 457f9018b9..9eeeb12643 100644
--- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration.h	
+++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR 1.4 Turbo/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration.h
index a66e2e4a37..226b699f40 100644
--- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration.h	
+++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h
index ddce724fba..8ffd39d6d3 100644
--- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h	
+++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration.h
index abe8b6f5ab..d27e6a5ce4 100644
--- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration.h	
+++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration.h b/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration.h
index 62b29ad208..c7ebbccace 100644
--- a/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration.h	
+++ b/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration.h b/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration.h
index ae0bef1c3f..da8a0f60f5 100644
--- a/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration.h	
+++ b/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration.h b/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration.h
index 080394e76a..0bc91fae02 100644
--- a/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration.h	
+++ b/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-3 V2/Configuration.h b/config/examples/Creality/Ender-3 V2/Configuration.h
index e7cc78192d..9e477513fd 100644
--- a/config/examples/Creality/Ender-3 V2/Configuration.h	
+++ b/config/examples/Creality/Ender-3 V2/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-3/BigTreeTech E3 RRF/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech E3 RRF/Configuration.h
index c1d9df9f25..a3fe711c81 100644
--- a/config/examples/Creality/Ender-3/BigTreeTech E3 RRF/Configuration.h	
+++ b/config/examples/Creality/Ender-3/BigTreeTech E3 RRF/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR 1.4/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR 1.4/Configuration.h
index 26bb92aeeb..5bc107d449 100644
--- a/config/examples/Creality/Ender-3/BigTreeTech SKR 1.4/Configuration.h	
+++ b/config/examples/Creality/Ender-3/BigTreeTech SKR 1.4/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration.h
index da3cd6d65a..52d9796cb1 100644
--- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration.h	
+++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration.h
index 827e3f1872..bb06938a4f 100644
--- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration.h	
+++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration.h
index 6e5e6ee609..f284cdb8f0 100644
--- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration.h	
+++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration.h
index 0fb86edc81..7d43b1ea13 100644
--- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration.h	
+++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h
index 457bf6dcdc..16821cdd38 100644
--- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h	
+++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h
index 161a4e8503..5f28c67b64 100644
--- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h	
+++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h
index ffed4bda61..1b41648dec 100644
--- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h	
+++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-3/CrealityV1/Configuration.h b/config/examples/Creality/Ender-3/CrealityV1/Configuration.h
index 977be8672d..9d54dec590 100644
--- a/config/examples/Creality/Ender-3/CrealityV1/Configuration.h
+++ b/config/examples/Creality/Ender-3/CrealityV1/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-3/CrealityV422/Configuration.h b/config/examples/Creality/Ender-3/CrealityV422/Configuration.h
index 6c59a4e69f..70abf1686b 100644
--- a/config/examples/Creality/Ender-3/CrealityV422/Configuration.h
+++ b/config/examples/Creality/Ender-3/CrealityV422/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-3/CrealityV427/Configuration.h b/config/examples/Creality/Ender-3/CrealityV427/Configuration.h
index 8dd93ea64b..ed65ee286c 100644
--- a/config/examples/Creality/Ender-3/CrealityV427/Configuration.h
+++ b/config/examples/Creality/Ender-3/CrealityV427/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h
index 52cd61ab1b..fa5ebbdf53 100644
--- a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h	
+++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h
index 8091a92ed4..d06c1b8682 100644
--- a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h	
+++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h
index a846a1f9d1..cad5c551c1 100644
--- a/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h	
+++ b/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h
index 8cc8b7bffb..944f313232 100644
--- a/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h	
+++ b/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h b/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h
index 2e1a07aa42..5fed062eb1 100644
--- a/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h
+++ b/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-3/MKS Robin E3/V1.0/Configuration.h b/config/examples/Creality/Ender-3/MKS Robin E3/V1.0/Configuration.h
index 7e7ba605ba..944a423d23 100644
--- a/config/examples/Creality/Ender-3/MKS Robin E3/V1.0/Configuration.h	
+++ b/config/examples/Creality/Ender-3/MKS Robin E3/V1.0/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-3/MKS Robin E3/V1.1/Configuration.h b/config/examples/Creality/Ender-3/MKS Robin E3/V1.1/Configuration.h
index 8c6463fe94..45991afdc4 100644
--- a/config/examples/Creality/Ender-3/MKS Robin E3/V1.1/Configuration.h	
+++ b/config/examples/Creality/Ender-3/MKS Robin E3/V1.1/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration.h b/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration.h
index 2611e95b61..72e152e168 100644
--- a/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration.h	
+++ b/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-4/Configuration.h b/config/examples/Creality/Ender-4/Configuration.h
index d2242d7c2e..cc4f602c62 100644
--- a/config/examples/Creality/Ender-4/Configuration.h
+++ b/config/examples/Creality/Ender-4/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-5 Plus/Configuration.h b/config/examples/Creality/Ender-5 Plus/Configuration.h
index 8c4b40d85b..150d78242b 100644
--- a/config/examples/Creality/Ender-5 Plus/Configuration.h	
+++ b/config/examples/Creality/Ender-5 Plus/Configuration.h	
@@ -399,70 +399,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h
index 6f222d1211..eaf61960ca 100644
--- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h	
+++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration.h
index 23b69e3898..02eaa64249 100644
--- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration.h	
+++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h
index f86ca55804..e957f73f15 100644
--- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h	
+++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/Configuration.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/Configuration.h
index 2ad180f6f6..92f33b71b6 100644
--- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/Configuration.h	
+++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 2.0 with BLTouch/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration.h b/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration.h
index 6b1db85eed..38560c20a9 100644
--- a/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration.h	
+++ b/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration.h b/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration.h
index 671f02da37..be3fb72101 100644
--- a/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration.h	
+++ b/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration.h b/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration.h
index 7846f5d8db..a39b92c555 100644
--- a/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration.h	
+++ b/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h
index c53b9dbe7f..d3f94f264c 100644
--- a/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h	
+++ b/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h	
@@ -407,70 +407,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #if ENABLED(E3D)
   #define TEMP_SENSOR_0 5
diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h
index fc4b9f5d53..5cc34d5baf 100644
--- a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h	
+++ b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration.h
index 15fd4567dc..0b58461bf4 100644
--- a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration.h	
+++ b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration.h
index 00c8311ae8..3c459ea9ed 100644
--- a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration.h	
+++ b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h
index ca92754b9b..8c6afd60c7 100644
--- a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h	
+++ b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-5/CrealityV1/Configuration.h b/config/examples/Creality/Ender-5/CrealityV1/Configuration.h
index ef4e4ec88f..3730c511a9 100644
--- a/config/examples/Creality/Ender-5/CrealityV1/Configuration.h
+++ b/config/examples/Creality/Ender-5/CrealityV1/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-5/CrealityV427/Configuration.h b/config/examples/Creality/Ender-5/CrealityV427/Configuration.h
index 07646c00f1..1b8e691e5c 100644
--- a/config/examples/Creality/Ender-5/CrealityV427/Configuration.h
+++ b/config/examples/Creality/Ender-5/CrealityV427/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Creality/Ender-6/Configuration.h b/config/examples/Creality/Ender-6/Configuration.h
index 318ab06a69..3121b928bd 100644
--- a/config/examples/Creality/Ender-6/Configuration.h
+++ b/config/examples/Creality/Ender-6/Configuration.h
@@ -400,70 +400,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Dagoma/Disco Ultimate/Configuration.h b/config/examples/Dagoma/Disco Ultimate/Configuration.h
index 87a57ad14c..7f28056631 100644
--- a/config/examples/Dagoma/Disco Ultimate/Configuration.h	
+++ b/config/examples/Dagoma/Disco Ultimate/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 18
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Daycom/3DP-100/Configuration.h b/config/examples/Daycom/3DP-100/Configuration.h
index 3bc396e3c5..7523818cd2 100644
--- a/config/examples/Daycom/3DP-100/Configuration.h
+++ b/config/examples/Daycom/3DP-100/Configuration.h
@@ -399,70 +399,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/EXP3D/Imprimante multifonction/Configuration.h b/config/examples/EXP3D/Imprimante multifonction/Configuration.h
index dc3d27ebb4..ba1a59a148 100644
--- a/config/examples/EXP3D/Imprimante multifonction/Configuration.h	
+++ b/config/examples/EXP3D/Imprimante multifonction/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Einstart-S/Configuration.h b/config/examples/Einstart-S/Configuration.h
index b46732d90d..c5b5d081ea 100644
--- a/config/examples/Einstart-S/Configuration.h
+++ b/config/examples/Einstart-S/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 666
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Eryone/Thinker SE/Configuration.h b/config/examples/Eryone/Thinker SE/Configuration.h
index 33bd47668b..3e078eab8d 100644
--- a/config/examples/Eryone/Thinker SE/Configuration.h	
+++ b/config/examples/Eryone/Thinker SE/Configuration.h	
@@ -403,70 +403,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 13
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Eryone/Thinker V2/Configuration.h b/config/examples/Eryone/Thinker V2/Configuration.h
index 6812dac24e..cbc4dc9897 100644
--- a/config/examples/Eryone/Thinker V2/Configuration.h	
+++ b/config/examples/Eryone/Thinker V2/Configuration.h	
@@ -403,70 +403,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 13
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/FYSETC/AIO_II/Configuration.h b/config/examples/FYSETC/AIO_II/Configuration.h
index d358ef6699..7d89210978 100644
--- a/config/examples/FYSETC/AIO_II/Configuration.h
+++ b/config/examples/FYSETC/AIO_II/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/FYSETC/F6_13/Configuration.h b/config/examples/FYSETC/F6_13/Configuration.h
index 7ee181d349..966376dee8 100644
--- a/config/examples/FYSETC/F6_13/Configuration.h
+++ b/config/examples/FYSETC/F6_13/Configuration.h
@@ -399,70 +399,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/FYSETC/S6/Configuration.h b/config/examples/FYSETC/S6/Configuration.h
index b0fa66be18..61ca0d57ae 100644
--- a/config/examples/FYSETC/S6/Configuration.h
+++ b/config/examples/FYSETC/S6/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Felix/DUAL/Configuration.h b/config/examples/Felix/DUAL/Configuration.h
index d0973a38ce..80d3bf7cdf 100644
--- a/config/examples/Felix/DUAL/Configuration.h
+++ b/config/examples/Felix/DUAL/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 1
diff --git a/config/examples/Felix/Single/Configuration.h b/config/examples/Felix/Single/Configuration.h
index d3edcd2b5c..6e4e849afa 100644
--- a/config/examples/Felix/Single/Configuration.h
+++ b/config/examples/Felix/Single/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/FlashForge/Creator 2X/Configuration.h b/config/examples/FlashForge/Creator 2X/Configuration.h
index 66f065f9b5..120d21470a 100644
--- a/config/examples/FlashForge/Creator 2X/Configuration.h	
+++ b/config/examples/FlashForge/Creator 2X/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 -2
 #define TEMP_SENSOR_1 -2
diff --git a/config/examples/FlashForge/CreatorPro/Configuration.h b/config/examples/FlashForge/CreatorPro/Configuration.h
index 572e5ab734..1818a1cd6a 100644
--- a/config/examples/FlashForge/CreatorPro/Configuration.h
+++ b/config/examples/FlashForge/CreatorPro/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 -2
 #define TEMP_SENSOR_1 -2
diff --git a/config/examples/FlyingBear/P905H/Configuration.h b/config/examples/FlyingBear/P905H/Configuration.h
index 376f841f7e..10cd663f95 100644
--- a/config/examples/FlyingBear/P905H/Configuration.h
+++ b/config/examples/FlyingBear/P905H/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/FoamCutter/Configuration.h b/config/examples/FoamCutter/Configuration.h
index 0e542ca3a5..d5689052cd 100644
--- a/config/examples/FoamCutter/Configuration.h
+++ b/config/examples/FoamCutter/Configuration.h
@@ -396,70 +396,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/FolgerTech/i3-2020/Configuration.h b/config/examples/FolgerTech/i3-2020/Configuration.h
index 7724739b32..0badec5b44 100644
--- a/config/examples/FolgerTech/i3-2020/Configuration.h
+++ b/config/examples/FolgerTech/i3-2020/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Formbot/Raptor/Configuration.h b/config/examples/Formbot/Raptor/Configuration.h
index 3998b6d4b0..045839fe9c 100644
--- a/config/examples/Formbot/Raptor/Configuration.h
+++ b/config/examples/Formbot/Raptor/Configuration.h
@@ -440,70 +440,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Formbot/T_Rex_2+/Configuration.h b/config/examples/Formbot/T_Rex_2+/Configuration.h
index 262e58c45e..3f5b757c48 100644
--- a/config/examples/Formbot/T_Rex_2+/Configuration.h
+++ b/config/examples/Formbot/T_Rex_2+/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 1
diff --git a/config/examples/Formbot/T_Rex_3/Configuration.h b/config/examples/Formbot/T_Rex_3/Configuration.h
index 804ce3ed0b..f709cbfa6e 100644
--- a/config/examples/Formbot/T_Rex_3/Configuration.h
+++ b/config/examples/Formbot/T_Rex_3/Configuration.h
@@ -400,70 +400,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 1
diff --git a/config/examples/Geeetech/A10/Configuration.h b/config/examples/Geeetech/A10/Configuration.h
index 257e80df76..be90c9c232 100644
--- a/config/examples/Geeetech/A10/Configuration.h
+++ b/config/examples/Geeetech/A10/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Geeetech/A10D/Configuration.h b/config/examples/Geeetech/A10D/Configuration.h
index 5bc1db09c9..2126243b14 100644
--- a/config/examples/Geeetech/A10D/Configuration.h
+++ b/config/examples/Geeetech/A10D/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 1
diff --git a/config/examples/Geeetech/A10M/Stock LCD/Configuration.h b/config/examples/Geeetech/A10M/Stock LCD/Configuration.h
index 0aee5b879d..9b659efa0d 100644
--- a/config/examples/Geeetech/A10M/Stock LCD/Configuration.h	
+++ b/config/examples/Geeetech/A10M/Stock LCD/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Geeetech/A10M/YHCB2004_V4.1/Configuration.h b/config/examples/Geeetech/A10M/YHCB2004_V4.1/Configuration.h
index 4d45d4ebf3..a20a95e106 100644
--- a/config/examples/Geeetech/A10M/YHCB2004_V4.1/Configuration.h
+++ b/config/examples/Geeetech/A10M/YHCB2004_V4.1/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Geeetech/A10PRO/Configuration.h b/config/examples/Geeetech/A10PRO/Configuration.h
index 8e46b8e24c..2cd19a4a66 100644
--- a/config/examples/Geeetech/A10PRO/Configuration.h
+++ b/config/examples/Geeetech/A10PRO/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Geeetech/A10T/Stock LCD/Configuration.h b/config/examples/Geeetech/A10T/Stock LCD/Configuration.h
index c87ff36706..d775d3789b 100644
--- a/config/examples/Geeetech/A10T/Stock LCD/Configuration.h	
+++ b/config/examples/Geeetech/A10T/Stock LCD/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Geeetech/A10T/YHCB2004_V4.1/Configuration.h b/config/examples/Geeetech/A10T/YHCB2004_V4.1/Configuration.h
index 36b3f33711..dab74e7c7b 100644
--- a/config/examples/Geeetech/A10T/YHCB2004_V4.1/Configuration.h
+++ b/config/examples/Geeetech/A10T/YHCB2004_V4.1/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Geeetech/A20/Configuration.h b/config/examples/Geeetech/A20/Configuration.h
index 6b64cf855c..246aa95081 100644
--- a/config/examples/Geeetech/A20/Configuration.h
+++ b/config/examples/Geeetech/A20/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Geeetech/A20M/Configuration.h b/config/examples/Geeetech/A20M/Configuration.h
index 6c25c60f10..0d64881826 100644
--- a/config/examples/Geeetech/A20M/Configuration.h
+++ b/config/examples/Geeetech/A20M/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Geeetech/A20T/Configuration.h b/config/examples/Geeetech/A20T/Configuration.h
index b69cc0ece2..69fc3a1604 100644
--- a/config/examples/Geeetech/A20T/Configuration.h
+++ b/config/examples/Geeetech/A20T/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Geeetech/A30/Configuration.h b/config/examples/Geeetech/A30/Configuration.h
index 65f57813e1..6998c8678e 100644
--- a/config/examples/Geeetech/A30/Configuration.h
+++ b/config/examples/Geeetech/A30/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Geeetech/A30M/Configuration.h b/config/examples/Geeetech/A30M/Configuration.h
index 4ebe513460..d7c252960a 100644
--- a/config/examples/Geeetech/A30M/Configuration.h
+++ b/config/examples/Geeetech/A30M/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Geeetech/A30T/Configuration.h b/config/examples/Geeetech/A30T/Configuration.h
index 794a683cb4..605b4349ba 100644
--- a/config/examples/Geeetech/A30T/Configuration.h
+++ b/config/examples/Geeetech/A30T/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Geeetech/D200/Configuration.h b/config/examples/Geeetech/D200/Configuration.h
index 9b12f50c06..77fbb3c403 100644
--- a/config/examples/Geeetech/D200/Configuration.h
+++ b/config/examples/Geeetech/D200/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Geeetech/Duplicator5/Configuration.h b/config/examples/Geeetech/Duplicator5/Configuration.h
index e7fda11354..b63c2e8053 100644
--- a/config/examples/Geeetech/Duplicator5/Configuration.h
+++ b/config/examples/Geeetech/Duplicator5/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 1
diff --git a/config/examples/Geeetech/E180/Configuration.h b/config/examples/Geeetech/E180/Configuration.h
index 985336cfc7..be9b868bd4 100644
--- a/config/examples/Geeetech/E180/Configuration.h
+++ b/config/examples/Geeetech/E180/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Geeetech/GT2560/Configuration.h b/config/examples/Geeetech/GT2560/Configuration.h
index 9988fcbe44..22fbc62190 100644
--- a/config/examples/Geeetech/GT2560/Configuration.h
+++ b/config/examples/Geeetech/GT2560/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
index 3ab08a2b96..a4d33eff36 100644
--- a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
+++ b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Geeetech/M201/Configuration.h b/config/examples/Geeetech/M201/Configuration.h
index df53887499..72a3ebb490 100644
--- a/config/examples/Geeetech/M201/Configuration.h
+++ b/config/examples/Geeetech/M201/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Geeetech/MeCreator2/Configuration.h b/config/examples/Geeetech/MeCreator2/Configuration.h
index 4490514716..aae7a71fc5 100644
--- a/config/examples/Geeetech/MeCreator2/Configuration.h
+++ b/config/examples/Geeetech/MeCreator2/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Geeetech/Me_creator/Configuration.h b/config/examples/Geeetech/Me_creator/Configuration.h
index ba9e957b1d..0395da3943 100644
--- a/config/examples/Geeetech/Me_creator/Configuration.h
+++ b/config/examples/Geeetech/Me_creator/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Geeetech/Me_ducer/Configuration.h b/config/examples/Geeetech/Me_ducer/Configuration.h
index 7f061a2dc9..80e4abd98c 100644
--- a/config/examples/Geeetech/Me_ducer/Configuration.h
+++ b/config/examples/Geeetech/Me_ducer/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Geeetech/PI3A PRO/Configuration.h b/config/examples/Geeetech/PI3A PRO/Configuration.h
index 971e339f48..90dfe9c081 100644
--- a/config/examples/Geeetech/PI3A PRO/Configuration.h	
+++ b/config/examples/Geeetech/PI3A PRO/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h
index 071502b47f..758772f1a7 100644
--- a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h	
+++ b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h
index 9b1f2a1be0..1761f08cad 100644
--- a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h	
+++ b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h
index 543fb8f3a0..0fd95c3019 100644
--- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h	
+++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 1
diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h
index 6d9eeb296a..edd858eab8 100644
--- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h	
+++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/HMS434/Configuration.h b/config/examples/HMS434/Configuration.h
index 5ffbf16a02..fc35013976 100644
--- a/config/examples/HMS434/Configuration.h
+++ b/config/examples/HMS434/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0      -1
 #define TEMP_SENSOR_1       0
diff --git a/config/examples/Infitary/i3-M508/Configuration.h b/config/examples/Infitary/i3-M508/Configuration.h
index 614e19d8ee..737b09fe33 100644
--- a/config/examples/Infitary/i3-M508/Configuration.h
+++ b/config/examples/Infitary/i3-M508/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Intamsys/FunmatHT 4988/Configuration.h b/config/examples/Intamsys/FunmatHT 4988/Configuration.h
index 127c0c1ab1..08b4c5f39c 100644
--- a/config/examples/Intamsys/FunmatHT 4988/Configuration.h	
+++ b/config/examples/Intamsys/FunmatHT 4988/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 20
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/JGAurora/A1/Configuration.h b/config/examples/JGAurora/A1/Configuration.h
index 04cab27250..c46b52d798 100644
--- a/config/examples/JGAurora/A1/Configuration.h
+++ b/config/examples/JGAurora/A1/Configuration.h
@@ -398,70 +398,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/JGAurora/A3/Configuration.h b/config/examples/JGAurora/A3/Configuration.h
index 296cf37722..ce9fcc43d2 100644
--- a/config/examples/JGAurora/A3/Configuration.h
+++ b/config/examples/JGAurora/A3/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/JGAurora/A5/Configuration.h b/config/examples/JGAurora/A5/Configuration.h
index 9bfd7b6554..0adf062b08 100644
--- a/config/examples/JGAurora/A5/Configuration.h
+++ b/config/examples/JGAurora/A5/Configuration.h
@@ -402,70 +402,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 15 // manual calibration of thermistor in JGAurora A5 hotend
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/JGAurora/A5S/Configuration.h b/config/examples/JGAurora/A5S/Configuration.h
index f7efb23968..e19a7c40d6 100644
--- a/config/examples/JGAurora/A5S/Configuration.h
+++ b/config/examples/JGAurora/A5S/Configuration.h
@@ -398,70 +398,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/JGAurora/Magic/Configuration.h b/config/examples/JGAurora/Magic/Configuration.h
index 850739ac21..975d9c2cbf 100644
--- a/config/examples/JGAurora/Magic/Configuration.h
+++ b/config/examples/JGAurora/Magic/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Kingroon/KP3/Configuration.h b/config/examples/Kingroon/KP3/Configuration.h
index 4a4d520c8c..ca12778524 100644
--- a/config/examples/Kingroon/KP3/Configuration.h
+++ b/config/examples/Kingroon/KP3/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Labists/ET4/Configuration.h b/config/examples/Labists/ET4/Configuration.h
index b521a71c34..a597b80763 100644
--- a/config/examples/Labists/ET4/Configuration.h
+++ b/config/examples/Labists/ET4/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/MBot/Cube/Configuration.h b/config/examples/MBot/Cube/Configuration.h
index e3bb72758c..264e8881cf 100644
--- a/config/examples/MBot/Cube/Configuration.h
+++ b/config/examples/MBot/Cube/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 -2
 #define TEMP_SENSOR_1 -2
diff --git a/config/examples/MakerFarm/Pegasus 12/Configuration.h b/config/examples/MakerFarm/Pegasus 12/Configuration.h
index 320627fd72..7418896772 100644
--- a/config/examples/MakerFarm/Pegasus 12/Configuration.h	
+++ b/config/examples/MakerFarm/Pegasus 12/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/MakerParts/Configuration.h b/config/examples/MakerParts/Configuration.h
index 5c70453a8c..6882e3bac1 100644
--- a/config/examples/MakerParts/Configuration.h
+++ b/config/examples/MakerParts/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Malyan/M150/Configuration.h b/config/examples/Malyan/M150/Configuration.h
index 1f05f79b06..b783ef4637 100644
--- a/config/examples/Malyan/M150/Configuration.h
+++ b/config/examples/Malyan/M150/Configuration.h
@@ -402,70 +402,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Malyan/M180/Configuration.h b/config/examples/Malyan/M180/Configuration.h
index d31c77837d..75b09d8985 100644
--- a/config/examples/Malyan/M180/Configuration.h
+++ b/config/examples/Malyan/M180/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 -2
 #define TEMP_SENSOR_1 -2
diff --git a/config/examples/Malyan/M200/Configuration.h b/config/examples/Malyan/M200/Configuration.h
index 91534dab6d..ff42344e2c 100644
--- a/config/examples/Malyan/M200/Configuration.h
+++ b/config/examples/Malyan/M200/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 11
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Micromake/C1/basic/Configuration.h b/config/examples/Micromake/C1/basic/Configuration.h
index 54fb4dfdb0..90a6297200 100644
--- a/config/examples/Micromake/C1/basic/Configuration.h
+++ b/config/examples/Micromake/C1/basic/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Micromake/C1/enhanced/Configuration.h b/config/examples/Micromake/C1/enhanced/Configuration.h
index a31848aa9c..ce06d06404 100644
--- a/config/examples/Micromake/C1/enhanced/Configuration.h
+++ b/config/examples/Micromake/C1/enhanced/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Mks/Robin/Configuration.h b/config/examples/Mks/Robin/Configuration.h
index 865588df5b..6f7b7d7d55 100644
--- a/config/examples/Mks/Robin/Configuration.h
+++ b/config/examples/Mks/Robin/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 1
diff --git a/config/examples/Mks/Robin_Lite3/Configuration.h b/config/examples/Mks/Robin_Lite3/Configuration.h
index 13fdadd12c..8d498c8799 100644
--- a/config/examples/Mks/Robin_Lite3/Configuration.h
+++ b/config/examples/Mks/Robin_Lite3/Configuration.h
@@ -404,70 +404,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Mks/Robin_Pro/Configuration.h b/config/examples/Mks/Robin_Pro/Configuration.h
index 96238701ca..471e10f3b4 100644
--- a/config/examples/Mks/Robin_Pro/Configuration.h
+++ b/config/examples/Mks/Robin_Pro/Configuration.h
@@ -399,70 +399,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Mks/Sbase/Configuration.h b/config/examples/Mks/Sbase/Configuration.h
index 41048c74f9..b165d8b0bf 100644
--- a/config/examples/Mks/Sbase/Configuration.h
+++ b/config/examples/Mks/Sbase/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Modix/Big60/Configuration.h b/config/examples/Modix/Big60/Configuration.h
index 7b732c0e13..b50e64ca03 100644
--- a/config/examples/Modix/Big60/Configuration.h
+++ b/config/examples/Modix/Big60/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Nextion/Configuration.h b/config/examples/Nextion/Configuration.h
index 8947c17bfb..7b02e8824b 100644
--- a/config/examples/Nextion/Configuration.h
+++ b/config/examples/Nextion/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Ortur 4/Configuration.h b/config/examples/Ortur 4/Configuration.h
index 02103a39ca..49fb879f76 100644
--- a/config/examples/Ortur 4/Configuration.h	
+++ b/config/examples/Ortur 4/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Printrbot/PrintrboardG2/Configuration.h b/config/examples/Printrbot/PrintrboardG2/Configuration.h
index 2634a7e636..64552c32cd 100644
--- a/config/examples/Printrbot/PrintrboardG2/Configuration.h
+++ b/config/examples/Printrbot/PrintrboardG2/Configuration.h
@@ -398,70 +398,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Printrbot/Simple Metal RevD/Configuration.h b/config/examples/Printrbot/Simple Metal RevD/Configuration.h
index 64f1817fe8..c17a888ea5 100644
--- a/config/examples/Printrbot/Simple Metal RevD/Configuration.h	
+++ b/config/examples/Printrbot/Simple Metal RevD/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Prusa/MK3/Configuration.h b/config/examples/Prusa/MK3/Configuration.h
index 65a3dd3d25..c7ad421123 100644
--- a/config/examples/Prusa/MK3/Configuration.h
+++ b/config/examples/Prusa/MK3/Configuration.h
@@ -416,70 +416,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h b/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h
index 10b49462d5..cdac95e32f 100644
--- a/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h
+++ b/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Qidi/Qidi 1/Configuration.h b/config/examples/Qidi/Qidi 1/Configuration.h
index 2359232c23..15bfa547c8 100644
--- a/config/examples/Qidi/Qidi 1/Configuration.h	
+++ b/config/examples/Qidi/Qidi 1/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 -2
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Raiscube/A8r/Configuration.h b/config/examples/Raiscube/A8r/Configuration.h
index 8397cdccce..719e07464b 100644
--- a/config/examples/Raiscube/A8r/Configuration.h
+++ b/config/examples/Raiscube/A8r/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 11
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/RapideLite/RL200/Configuration.h b/config/examples/RapideLite/RL200/Configuration.h
index 8ef01ee2b2..942cf2ba71 100644
--- a/config/examples/RapideLite/RL200/Configuration.h
+++ b/config/examples/RapideLite/RL200/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Renkforce/RF100/Configuration.h b/config/examples/Renkforce/RF100/Configuration.h
index 1d35017c35..b86e875d5d 100644
--- a/config/examples/Renkforce/RF100/Configuration.h
+++ b/config/examples/Renkforce/RF100/Configuration.h
@@ -400,70 +400,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Renkforce/RF100XL/Configuration.h b/config/examples/Renkforce/RF100XL/Configuration.h
index edfc0c1bfe..b18b9cd1fc 100644
--- a/config/examples/Renkforce/RF100XL/Configuration.h
+++ b/config/examples/Renkforce/RF100XL/Configuration.h
@@ -400,70 +400,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Renkforce/RF100v2/Configuration.h b/config/examples/Renkforce/RF100v2/Configuration.h
index dde0bc6459..7e5fc76bb4 100644
--- a/config/examples/Renkforce/RF100v2/Configuration.h
+++ b/config/examples/Renkforce/RF100v2/Configuration.h
@@ -400,70 +400,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/RepRapPro/Huxley/Configuration.h b/config/examples/RepRapPro/Huxley/Configuration.h
index 1ffaa32fd7..05f1b0f147 100644
--- a/config/examples/RepRapPro/Huxley/Configuration.h
+++ b/config/examples/RepRapPro/Huxley/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/RepRapWorld/Megatronics/Configuration.h b/config/examples/RepRapWorld/Megatronics/Configuration.h
index cf0bc4f171..87424ff00f 100644
--- a/config/examples/RepRapWorld/Megatronics/Configuration.h
+++ b/config/examples/RepRapWorld/Megatronics/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/RigidBot/Configuration.h b/config/examples/RigidBot/Configuration.h
index 490e736a31..7d21cef6ac 100644
--- a/config/examples/RigidBot/Configuration.h
+++ b/config/examples/RigidBot/Configuration.h
@@ -400,70 +400,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1 // DGlass3D = 5; RigidBot = 1; 3DSv6 = 5
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Robo3D/R1+/Configuration.h b/config/examples/Robo3D/R1+/Configuration.h
index f32388bf34..fca444c5a7 100644
--- a/config/examples/Robo3D/R1+/Configuration.h
+++ b/config/examples/Robo3D/R1+/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/SCARA/MP_SCARA/Configuration.h b/config/examples/SCARA/MP_SCARA/Configuration.h
index 09d3e69f17..9ca524aa4f 100644
--- a/config/examples/SCARA/MP_SCARA/Configuration.h
+++ b/config/examples/SCARA/MP_SCARA/Configuration.h
@@ -442,70 +442,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/SCARA/Morgan/Configuration.h b/config/examples/SCARA/Morgan/Configuration.h
index dfd32c5cbd..05912c5f57 100644
--- a/config/examples/SCARA/Morgan/Configuration.h
+++ b/config/examples/SCARA/Morgan/Configuration.h
@@ -442,70 +442,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration.h b/config/examples/STM32/Black_STM32F407VET6/Configuration.h
index 7c2ee7e87c..1fd5eb97d0 100644
--- a/config/examples/STM32/Black_STM32F407VET6/Configuration.h
+++ b/config/examples/STM32/Black_STM32F407VET6/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 1
diff --git a/config/examples/STM32/STM32F103RE/Configuration.h b/config/examples/STM32/STM32F103RE/Configuration.h
index b9fd3e0504..2f3292c6dd 100644
--- a/config/examples/STM32/STM32F103RE/Configuration.h
+++ b/config/examples/STM32/STM32F103RE/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #warning temp_sensor set to 998/999 (fake)
 #define TEMP_SENSOR_0 999
diff --git a/config/examples/STM32/STM32F4/Configuration.h b/config/examples/STM32/STM32F4/Configuration.h
index 967301cc69..7fda292f7a 100644
--- a/config/examples/STM32/STM32F4/Configuration.h
+++ b/config/examples/STM32/STM32F4/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Sanguinololu/Configuration.h b/config/examples/Sanguinololu/Configuration.h
index 718105ed68..fe077fae24 100644
--- a/config/examples/Sanguinololu/Configuration.h
+++ b/config/examples/Sanguinololu/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 2.0/Configuration.h
index 91df1e1a43..e348ae9a40 100644
--- a/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 2.0/Configuration.h	
+++ b/config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 2.0/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Sovol/SV-01/CrealityV22/Configuration.h b/config/examples/Sovol/SV-01/CrealityV22/Configuration.h
index 5cfab73dfc..ddae7cea98 100644
--- a/config/examples/Sovol/SV-01/CrealityV22/Configuration.h
+++ b/config/examples/Sovol/SV-01/CrealityV22/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Sovol/SV-01/CrealityV221/Configuration.h b/config/examples/Sovol/SV-01/CrealityV221/Configuration.h
index 0fe2ae5cc2..c69316532f 100644
--- a/config/examples/Sovol/SV-01/CrealityV221/Configuration.h
+++ b/config/examples/Sovol/SV-01/CrealityV221/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Sunlu/S8/Configuration.h b/config/examples/Sunlu/S8/Configuration.h
index 330d9a3859..c840155810 100644
--- a/config/examples/Sunlu/S8/Configuration.h
+++ b/config/examples/Sunlu/S8/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/TPARA/AXEL_TPARA/Configuration.h b/config/examples/TPARA/AXEL_TPARA/Configuration.h
index 7f27b1f92f..490e79baa4 100644
--- a/config/examples/TPARA/AXEL_TPARA/Configuration.h
+++ b/config/examples/TPARA/AXEL_TPARA/Configuration.h
@@ -417,70 +417,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Tevo/Michelangelo/Configuration.h b/config/examples/Tevo/Michelangelo/Configuration.h
index 7452bbf5f9..81d8c789c4 100644
--- a/config/examples/Tevo/Michelangelo/Configuration.h
+++ b/config/examples/Tevo/Michelangelo/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Tevo/Nereus/Configuration.h b/config/examples/Tevo/Nereus/Configuration.h
index 4d1b93079f..818960f6c8 100644
--- a/config/examples/Tevo/Nereus/Configuration.h
+++ b/config/examples/Tevo/Nereus/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Tevo/Tarantula Pro/Configuration.h b/config/examples/Tevo/Tarantula Pro/Configuration.h
index 22dd4ce722..c2b5088003 100644
--- a/config/examples/Tevo/Tarantula Pro/Configuration.h	
+++ b/config/examples/Tevo/Tarantula Pro/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h
index 27e2163ade..b5307e09a8 100644
--- a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h	
+++ b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h
index 14a67623d2..4927d81445 100644
--- a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h	
+++ b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/TheBorg/Configuration.h b/config/examples/TheBorg/Configuration.h
index 99b12a4e3c..7afb72ecc7 100644
--- a/config/examples/TheBorg/Configuration.h
+++ b/config/examples/TheBorg/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/TinyBoy2/Configuration.h b/config/examples/TinyBoy2/Configuration.h
index fdaefa3600..4abd849a39 100644
--- a/config/examples/TinyBoy2/Configuration.h
+++ b/config/examples/TinyBoy2/Configuration.h
@@ -419,70 +419,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Tronxy/X1/Configuration.h b/config/examples/Tronxy/X1/Configuration.h
index 57c74f4cad..d5b7a95fe1 100644
--- a/config/examples/Tronxy/X1/Configuration.h
+++ b/config/examples/Tronxy/X1/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 11
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Tronxy/X3A/Configuration.h b/config/examples/Tronxy/X3A/Configuration.h
index ecf52ed3f2..8d0da35315 100644
--- a/config/examples/Tronxy/X3A/Configuration.h
+++ b/config/examples/Tronxy/X3A/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 6
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Tronxy/X5S-2E/Configuration.h b/config/examples/Tronxy/X5S-2E/Configuration.h
index d03051ad83..ed00b1762b 100644
--- a/config/examples/Tronxy/X5S-2E/Configuration.h
+++ b/config/examples/Tronxy/X5S-2E/Configuration.h
@@ -399,70 +399,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Tronxy/X5S/Configuration.h b/config/examples/Tronxy/X5S/Configuration.h
index 63cf192447..8567b4767a 100644
--- a/config/examples/Tronxy/X5S/Configuration.h
+++ b/config/examples/Tronxy/X5S/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Tronxy/X5SA/Configuration.h b/config/examples/Tronxy/X5SA/Configuration.h
index 708b3c8c59..41e79a78c0 100644
--- a/config/examples/Tronxy/X5SA/Configuration.h
+++ b/config/examples/Tronxy/X5SA/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Tronxy/XY100/Configuration.h b/config/examples/Tronxy/XY100/Configuration.h
index 8f37b5e7a2..65f8b569c9 100644
--- a/config/examples/Tronxy/XY100/Configuration.h
+++ b/config/examples/Tronxy/XY100/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Two Trees/BlueR Plus/Configuration.h b/config/examples/Two Trees/BlueR Plus/Configuration.h
index 196a926ef5..68fd71aab6 100644
--- a/config/examples/Two Trees/BlueR Plus/Configuration.h	
+++ b/config/examples/Two Trees/BlueR Plus/Configuration.h	
@@ -398,70 +398,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Two Trees/BlueR/BlueR V1/Configuration.h b/config/examples/Two Trees/BlueR/BlueR V1/Configuration.h
index 8e1b478b01..9fee59067c 100644
--- a/config/examples/Two Trees/BlueR/BlueR V1/Configuration.h	
+++ b/config/examples/Two Trees/BlueR/BlueR V1/Configuration.h	
@@ -400,70 +400,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Two Trees/BlueR/BlueR V2/Configuration.h b/config/examples/Two Trees/BlueR/BlueR V2/Configuration.h
index 0793687dee..08affb6fe3 100644
--- a/config/examples/Two Trees/BlueR/BlueR V2/Configuration.h	
+++ b/config/examples/Two Trees/BlueR/BlueR V2/Configuration.h	
@@ -401,70 +401,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Two Trees/BlueR/BlueR V3/Configuration.h b/config/examples/Two Trees/BlueR/BlueR V3/Configuration.h
index a3ea308279..cc5668f7c6 100644
--- a/config/examples/Two Trees/BlueR/BlueR V3/Configuration.h	
+++ b/config/examples/Two Trees/BlueR/BlueR V3/Configuration.h	
@@ -400,70 +400,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration.h b/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration.h
index 253929ede5..642b5fb609 100644
--- a/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration.h	
+++ b/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration.h	
@@ -403,70 +403,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Two Trees/Sapphire Pro/Configuration.h b/config/examples/Two Trees/Sapphire Pro/Configuration.h
index 70e812aa19..bbf7a4d706 100644
--- a/config/examples/Two Trees/Sapphire Pro/Configuration.h	
+++ b/config/examples/Two Trees/Sapphire Pro/Configuration.h	
@@ -401,70 +401,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/UltiMachine/Archim1/Configuration.h b/config/examples/UltiMachine/Archim1/Configuration.h
index 227798021a..4d27864cca 100644
--- a/config/examples/UltiMachine/Archim1/Configuration.h
+++ b/config/examples/UltiMachine/Archim1/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/UltiMachine/Archim2/Configuration.h b/config/examples/UltiMachine/Archim2/Configuration.h
index 9b75dabbbb..972b30da4c 100644
--- a/config/examples/UltiMachine/Archim2/Configuration.h
+++ b/config/examples/UltiMachine/Archim2/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration.h b/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration.h
index 06673876a8..17c3d5864f 100644
--- a/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration.h	
+++ b/config/examples/Ultimaker/Ultimaker Original (1.5.7)/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 -1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Ultimaker/Ultimaker Original Plus (2.1.1)/Configuration.h b/config/examples/Ultimaker/Ultimaker Original Plus (2.1.1)/Configuration.h
index 45198e2340..8b77ff5739 100644
--- a/config/examples/Ultimaker/Ultimaker Original Plus (2.1.1)/Configuration.h	
+++ b/config/examples/Ultimaker/Ultimaker Original Plus (2.1.1)/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 20
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/VORONDesign/Configuration.h b/config/examples/VORONDesign/Configuration.h
index 24d1a7f0b8..45c7345e86 100644
--- a/config/examples/VORONDesign/Configuration.h
+++ b/config/examples/VORONDesign/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 5
diff --git a/config/examples/Velleman/K8200/Configuration.h b/config/examples/Velleman/K8200/Configuration.h
index cbd5bd2645..b32fdbc5a8 100644
--- a/config/examples/Velleman/K8200/Configuration.h
+++ b/config/examples/Velleman/K8200/Configuration.h
@@ -417,70 +417,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Velleman/K8400/Dual-head/Configuration.h b/config/examples/Velleman/K8400/Dual-head/Configuration.h
index dfdebc31e5..6dc459779c 100644
--- a/config/examples/Velleman/K8400/Dual-head/Configuration.h
+++ b/config/examples/Velleman/K8400/Dual-head/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 5
diff --git a/config/examples/Velleman/K8400/Single-head/Configuration.h b/config/examples/Velleman/K8400/Single-head/Configuration.h
index e7f8592c6e..238b3ec1e1 100644
--- a/config/examples/Velleman/K8400/Single-head/Configuration.h
+++ b/config/examples/Velleman/K8400/Single-head/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/WASP/PowerWASP/Configuration.h b/config/examples/WASP/PowerWASP/Configuration.h
index 0ce3485aa4..9c5ebf852c 100644
--- a/config/examples/WASP/PowerWASP/Configuration.h
+++ b/config/examples/WASP/PowerWASP/Configuration.h
@@ -410,70 +410,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 -1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Wanhao/Duplicator 4S/Configuration.h b/config/examples/Wanhao/Duplicator 4S/Configuration.h
index e06ecd3fd2..3cb31acc26 100644
--- a/config/examples/Wanhao/Duplicator 4S/Configuration.h	
+++ b/config/examples/Wanhao/Duplicator 4S/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 -2
 #define TEMP_SENSOR_1 -2
diff --git a/config/examples/Wanhao/Duplicator 6/Configuration.h b/config/examples/Wanhao/Duplicator 6/Configuration.h
index b273facc78..10d34d410d 100644
--- a/config/examples/Wanhao/Duplicator 6/Configuration.h	
+++ b/config/examples/Wanhao/Duplicator 6/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 20
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h b/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h
index 3b0f217ebe..8d848b0a05 100644
--- a/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h	
+++ b/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 99
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h b/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h
index af50ce8818..9225784e5e 100644
--- a/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h	
+++ b/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 13
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Wanhao/Duplicator i3 Plus/Configuration.h b/config/examples/Wanhao/Duplicator i3 Plus/Configuration.h
index 1455899d2d..8fbc177155 100644
--- a/config/examples/Wanhao/Duplicator i3 Plus/Configuration.h	
+++ b/config/examples/Wanhao/Duplicator i3 Plus/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Weistek/wt150/Configuration.h b/config/examples/Weistek/wt150/Configuration.h
index e09f986f85..aa4e19efad 100644
--- a/config/examples/Weistek/wt150/Configuration.h
+++ b/config/examples/Weistek/wt150/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 -2
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Zonestar/P802M/Configuration.h b/config/examples/Zonestar/P802M/Configuration.h
index a40796fc37..da6b5833c5 100644
--- a/config/examples/Zonestar/P802M/Configuration.h
+++ b/config/examples/Zonestar/P802M/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 501
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h
index d3a666ae24..03da91752b 100755
--- a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h	
+++ b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h	
@@ -399,70 +399,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 5
diff --git a/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h b/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h
index 81042657cc..32184353de 100644
--- a/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h	
+++ b/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h	
@@ -409,70 +409,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/delta/Anycubic/Kossel/Configuration.h b/config/examples/delta/Anycubic/Kossel/Configuration.h
index 13fbb79420..82a3b9f561 100644
--- a/config/examples/delta/Anycubic/Kossel/Configuration.h
+++ b/config/examples/delta/Anycubic/Kossel/Configuration.h
@@ -412,70 +412,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/delta/Anycubic/Predator/Configuration.h b/config/examples/delta/Anycubic/Predator/Configuration.h
index 542c92aa06..57c94e5f4b 100644
--- a/config/examples/delta/Anycubic/Predator/Configuration.h
+++ b/config/examples/delta/Anycubic/Predator/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/delta/Dreammaker/Overlord/Configuration.h b/config/examples/delta/Dreammaker/Overlord/Configuration.h
index 5f1a12dae7..e9c1c682b0 100644
--- a/config/examples/delta/Dreammaker/Overlord/Configuration.h
+++ b/config/examples/delta/Dreammaker/Overlord/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 201
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h
index e838fea443..9019564738 100644
--- a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h
+++ b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 201
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/delta/FLSUN/Q5-nano_v1/Configuration.h b/config/examples/delta/FLSUN/Q5-nano_v1/Configuration.h
index 4488dc8686..081a9175a1 100644
--- a/config/examples/delta/FLSUN/Q5-nano_v1/Configuration.h
+++ b/config/examples/delta/FLSUN/Q5-nano_v1/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/delta/FLSUN/Q5-nano_v2/Configuration.h b/config/examples/delta/FLSUN/Q5-nano_v2/Configuration.h
index c0e07d1378..f4c84c563f 100644
--- a/config/examples/delta/FLSUN/Q5-nano_v2/Configuration.h
+++ b/config/examples/delta/FLSUN/Q5-nano_v2/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/delta/FLSUN/QQ-S/Configuration.h b/config/examples/delta/FLSUN/QQ-S/Configuration.h
index 05fab75130..e37586d326 100644
--- a/config/examples/delta/FLSUN/QQ-S/Configuration.h
+++ b/config/examples/delta/FLSUN/QQ-S/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/delta/FLSUN/QQS-Pro/Configuration.h b/config/examples/delta/FLSUN/QQS-Pro/Configuration.h
index a3a84c9a4b..42e84a2600 100644
--- a/config/examples/delta/FLSUN/QQS-Pro/Configuration.h
+++ b/config/examples/delta/FLSUN/QQS-Pro/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
index 50af23412e..2e18731488 100644
--- a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
+++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/delta/FLSUN/kossel/Configuration.h b/config/examples/delta/FLSUN/kossel/Configuration.h
index 05d2534dd9..b14c96bf22 100644
--- a/config/examples/delta/FLSUN/kossel/Configuration.h
+++ b/config/examples/delta/FLSUN/kossel/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration.h b/config/examples/delta/FLSUN/kossel_mini/Configuration.h
index 34be6bd1f6..f6b4011edc 100644
--- a/config/examples/delta/FLSUN/kossel_mini/Configuration.h
+++ b/config/examples/delta/FLSUN/kossel_mini/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/delta/Geeetech/G2/Configuration.h b/config/examples/delta/Geeetech/G2/Configuration.h
index 3379b6fa58..471e795f19 100644
--- a/config/examples/delta/Geeetech/G2/Configuration.h
+++ b/config/examples/delta/Geeetech/G2/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0 // G2S 1
diff --git a/config/examples/delta/Geeetech/G2Pro/Configuration.h b/config/examples/delta/Geeetech/G2Pro/Configuration.h
index 53a976152d..cbc1a1ef62 100644
--- a/config/examples/delta/Geeetech/G2Pro/Configuration.h
+++ b/config/examples/delta/Geeetech/G2Pro/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0 // G2S 1
diff --git a/config/examples/delta/Geeetech/G2S/Configuration.h b/config/examples/delta/Geeetech/G2S/Configuration.h
index 2ff33e2327..db5a1e0f77 100644
--- a/config/examples/delta/Geeetech/G2S/Configuration.h
+++ b/config/examples/delta/Geeetech/G2S/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 1 // G2S 1
diff --git a/config/examples/delta/Geeetech/G2SPro/Configuration.h b/config/examples/delta/Geeetech/G2SPro/Configuration.h
index 7180b77437..f75851dccd 100644
--- a/config/examples/delta/Geeetech/G2SPro/Configuration.h
+++ b/config/examples/delta/Geeetech/G2SPro/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 1 // G2S 1
diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration.h b/config/examples/delta/Geeetech/Rostock 301/Configuration.h
index f76ab52a2c..4e15374f33 100644
--- a/config/examples/delta/Geeetech/Rostock 301/Configuration.h	
+++ b/config/examples/delta/Geeetech/Rostock 301/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 22
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/delta/Hatchbox_Alpha/Configuration.h b/config/examples/delta/Hatchbox_Alpha/Configuration.h
index 37dd78ded2..951d02ccf4 100644
--- a/config/examples/delta/Hatchbox_Alpha/Configuration.h
+++ b/config/examples/delta/Hatchbox_Alpha/Configuration.h
@@ -402,70 +402,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/delta/MKS/SBASE/Configuration.h b/config/examples/delta/MKS/SBASE/Configuration.h
index 754be50cf7..1f79d2472f 100644
--- a/config/examples/delta/MKS/SBASE/Configuration.h
+++ b/config/examples/delta/MKS/SBASE/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 -1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/delta/Malyan M300/Configuration.h b/config/examples/delta/Malyan M300/Configuration.h
index 3e1af599ba..8b4b5b6127 100644
--- a/config/examples/delta/Malyan M300/Configuration.h	
+++ b/config/examples/delta/Malyan M300/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 11
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/delta/Tevo Little Monster/Configuration.h b/config/examples/delta/Tevo Little Monster/Configuration.h
index 25bb640d0f..3c28d8dc35 100644
--- a/config/examples/delta/Tevo Little Monster/Configuration.h	
+++ b/config/examples/delta/Tevo Little Monster/Configuration.h	
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/delta/generic/Configuration.h b/config/examples/delta/generic/Configuration.h
index 2c9f9ea8e9..e3bbed454a 100644
--- a/config/examples/delta/generic/Configuration.h
+++ b/config/examples/delta/generic/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 -1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/delta/kossel_clear/Configuration.h b/config/examples/delta/kossel_clear/Configuration.h
index a88e02afa5..e897180d93 100644
--- a/config/examples/delta/kossel_clear/Configuration.h
+++ b/config/examples/delta/kossel_clear/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/delta/kossel_mini/Configuration.h b/config/examples/delta/kossel_mini/Configuration.h
index 0fef183a44..30cb771469 100644
--- a/config/examples/delta/kossel_mini/Configuration.h
+++ b/config/examples/delta/kossel_mini/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 7
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/delta/kossel_pro/Configuration.h b/config/examples/delta/kossel_pro/Configuration.h
index 4b49c60354..6c94699cd1 100644
--- a/config/examples/delta/kossel_pro/Configuration.h
+++ b/config/examples/delta/kossel_pro/Configuration.h
@@ -401,70 +401,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/delta/kossel_xl/Configuration.h b/config/examples/delta/kossel_xl/Configuration.h
index 7795789878..9bf8a1fcf9 100644
--- a/config/examples/delta/kossel_xl/Configuration.h
+++ b/config/examples/delta/kossel_xl/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/gCreate/gMax1.5+/Configuration.h b/config/examples/gCreate/gMax1.5+/Configuration.h
index e575b74621..33013abdc2 100644
--- a/config/examples/gCreate/gMax1.5+/Configuration.h
+++ b/config/examples/gCreate/gMax1.5+/Configuration.h
@@ -401,70 +401,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/linear_axes/RAMPS 5 LINEAR_AXES/Configuration.h b/config/examples/linear_axes/RAMPS 5 LINEAR_AXES/Configuration.h
index 8aab741799..ceb90e1f1c 100644
--- a/config/examples/linear_axes/RAMPS 5 LINEAR_AXES/Configuration.h	
+++ b/config/examples/linear_axes/RAMPS 5 LINEAR_AXES/Configuration.h	
@@ -399,70 +399,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/makibox/Configuration.h b/config/examples/makibox/Configuration.h
index dceb60943a..6d40a8f0eb 100644
--- a/config/examples/makibox/Configuration.h
+++ b/config/examples/makibox/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0
diff --git a/config/examples/tvrrug/Round2/Configuration.h b/config/examples/tvrrug/Round2/Configuration.h
index f39ce0c4e7..c6074bbddc 100644
--- a/config/examples/tvrrug/Round2/Configuration.h
+++ b/config/examples/tvrrug/Round2/Configuration.h
@@ -397,70 +397,92 @@
 // @section temperature
 
 /**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
  *
  * Temperature sensors available:
  *
- *    -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- *    -3 : thermocouple with MAX31855 (only for sensors 0-1)
- *    -2 : thermocouple with MAX6675 (only for sensors 0-1)
- *    -4 : thermocouple with AD8495
- *    -1 : thermocouple with AD595
+ *  SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ *  -------
+ *    -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire  (only for sensors 0-1)
+ *                  NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ *    -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ *    -2 : MAX6675  with Thermocouple, 0°C to +700°C    (only for sensors 0-1)
+ *
+ *  NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ *        Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ *        Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ *        Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ *  Analog Themocouple Boards
+ *  -------
+ *    -4 : AD8495 with Thermocouple
+ *    -1 : AD595  with Thermocouple
+ *
+ *  Analog Thermistors - 4.7kΩ pullup - Normal
+ *  -------
+ *     1 : 100kΩ  EPCOS - Best choice for EPCOS thermistors
+ *   331 : 100kΩ  Same as #1, but 3.3V scaled for MEGA
+ *   332 : 100kΩ  Same as #1, but 3.3V scaled for DUE
+ *     2 : 200kΩ  ATC Semitec 204GT-2
+ *   202 : 200kΩ  Copymaster 3D
+ *     3 : ???Ω   Mendel-parts thermistor
+ *     4 : 10kΩ   Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ *     5 : 100kΩ  ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ *   501 : 100kΩ  Zonestar - Tronxy X3A
+ *   502 : 100kΩ  Zonestar - used by hot bed in Zonestar Průša P802M
+ *   512 : 100kΩ  RPW-Ultra hotend
+ *     6 : 100kΩ  EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ *     7 : 100kΩ  Honeywell 135-104LAG-J01
+ *    71 : 100kΩ  Honeywell 135-104LAF-J01
+ *     8 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT
+ *     9 : 100kΩ  GE Sensing AL03006-58.2K-97-G1
+ *    10 : 100kΩ  RS PRO 198-961
+ *    11 : 100kΩ  Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ *    12 : 100kΩ  Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ *    13 : 100kΩ  Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ *    15 : 100kΩ  Calibrated for JGAurora A5 hotend
+ *    18 : 200kΩ  ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ *    22 : 100kΩ  GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ *    23 : 100kΩ  GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
+ *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    67 : 500kΩ  SliceEngineering 450°C Thermistor
+ *    70 : 100kΩ  bq Hephestos 2
+ *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ *  -------                           (but gives greater accuracy and more stable PID)
+ *    51 : 100kΩ  EPCOS (1kΩ pullup)
+ *    52 : 200kΩ  ATC Semitec 204GT-2 (1kΩ pullup)
+ *    55 : 100kΩ  ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ *  Analog Thermistors - 10kΩ pullup - Atypical
+ *  -------
+ *    99 : 100kΩ  Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ *  Analog RTDs (Pt100/Pt1000)
+ *  -------
+ *   110 : Pt100  with 1kΩ pullup (atypical)
+ *   147 : Pt100  with 4.7kΩ pullup
+ *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ *    21 : Pt100  with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ *  Custom / Dummy / Other
+ *  ------
  *     0 : not used
- *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- *   331 : (3.3V scaled thermistor 1 table for MEGA)
- *   332 : (3.3V scaled thermistor 1 table for DUE)
- *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- *   202 : 200k thermistor - Copymaster 3D
- *     3 : Mendel-parts thermistor (4.7k pullup)
- *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- *   501 : 100K Zonestar (Tronxy X3A) Thermistor
- *   502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- *    10 : 100k RS thermistor 198-961 (4.7k pullup)
- *    11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- *    15 : 100k thermistor calibration for JGAurora A5 hotend
- *    18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- *    20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- *         NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- *    21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- *         NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- *    22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- *    23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- *    30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- *   201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- *    61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- *    66 : 4.7M High Temperature thermistor from Dyze Design
- *    67 : 450C thermistor from SliceEngineering
- *    70 : the 100K thermistor found in the bq Hephestos 2
- *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *    99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- *                              (but gives greater accuracy and more stable PID)
- *    51 : 100k thermistor - EPCOS (1k pullup)
- *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- *  1047 : Pt1000 with 4k7 pullup (E3D)
- *  1010 : Pt1000 with 1k pullup (non standard)
- *   147 : Pt100 with 4k7 pullup
- *   110 : Pt100 with 1k pullup (non standard)
- *
  *  1000 : Custom - Specify parameters in Configuration_adv.h
  *
- *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
  */
 #define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0