diff --git a/config/examples/BIQU/B1-BLTouch/Configuration.h b/config/examples/BIQU/B1-BLTouch/Configuration.h
index 04aecdf837..d64e14b1f7 100644
--- a/config/examples/BIQU/B1-BLTouch/Configuration.h
+++ b/config/examples/BIQU/B1-BLTouch/Configuration.h
@@ -1190,10 +1190,11 @@
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
-  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_STATE     LOW   // Pin state indicating that filament is NOT present.
-  #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
-  //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
+  #define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500.
+  #define NUM_RUNOUT_SENSORS   1          // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
+  #define FIL_RUNOUT_STATE     LOW        // Pin state indicating that filament is NOT present.
+  #define FIL_RUNOUT_PULLUP               // Use internal pullup for filament runout pins.
+  //#define FIL_RUNOUT_PULLDOWN           // Use internal pulldown for filament runout pins.
 
   // Set one or more commands to execute on filament runout.
   // (After 'M412 H' Marlin will ask the host to handle the process.)
@@ -2294,6 +2295,10 @@
 
 // @section extras
 
+// Set number of user-controlled fans. Disable to use all board-defined fans.
+// :[1,2,3,4,5,6,7,8]
+//#define NUM_M106_FANS 1
+
 // Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
 //#define FAST_PWM_FAN
 
diff --git a/config/examples/BIQU/B1-BLTouch/Configuration_adv.h b/config/examples/BIQU/B1-BLTouch/Configuration_adv.h
index 7a1b27fa26..84a0508280 100644
--- a/config/examples/BIQU/B1-BLTouch/Configuration_adv.h
+++ b/config/examples/BIQU/B1-BLTouch/Configuration_adv.h
@@ -2092,10 +2092,10 @@
   #define FILAMENT_CHANGE_ALERT_BEEPS         10  // Number of alert beeps to play when a response is needed.
   #define PAUSE_PARK_NO_STEPPER_TIMEOUT           // Enable for XYZ steppers to stay powered on during filament change.
 
-  #define PARK_HEAD_ON_PAUSE                    // Park the nozzle during pause and filament change.
-  #define HOME_BEFORE_FILAMENT_CHANGE           // If needed, home before parking for filament change
+  #define PARK_HEAD_ON_PAUSE                      // Park the nozzle during pause and filament change.
+  #define HOME_BEFORE_FILAMENT_CHANGE             // If needed, home before parking for filament change
 
-  #define FILAMENT_LOAD_UNLOAD_GCODES           // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
+  #define FILAMENT_LOAD_UNLOAD_GCODES             // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
   //#define FILAMENT_UNLOAD_ALL_EXTRUDERS         // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
 #endif
 
diff --git a/config/examples/BIQU/B1/Configuration.h b/config/examples/BIQU/B1/Configuration.h
index 28e5682011..9b420b7d8d 100644
--- a/config/examples/BIQU/B1/Configuration.h
+++ b/config/examples/BIQU/B1/Configuration.h
@@ -1190,10 +1190,11 @@
  */
 //#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
-  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_STATE     LOW   // Pin state indicating that filament is NOT present.
-  #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
-  //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
+  #define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500.
+  #define NUM_RUNOUT_SENSORS   1          // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
+  #define FIL_RUNOUT_STATE     LOW        // Pin state indicating that filament is NOT present.
+  #define FIL_RUNOUT_PULLUP               // Use internal pullup for filament runout pins.
+  //#define FIL_RUNOUT_PULLDOWN           // Use internal pulldown for filament runout pins.
 
   // Set one or more commands to execute on filament runout.
   // (After 'M412 H' Marlin will ask the host to handle the process.)
@@ -2294,6 +2295,10 @@
 
 // @section extras
 
+// Set number of user-controlled fans. Disable to use all board-defined fans.
+// :[1,2,3,4,5,6,7,8]
+//#define NUM_M106_FANS 1
+
 // Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
 //#define FAST_PWM_FAN
 
diff --git a/config/examples/BIQU/B1/Configuration_adv.h b/config/examples/BIQU/B1/Configuration_adv.h
index 8df81698ef..a6bd49dbd7 100644
--- a/config/examples/BIQU/B1/Configuration_adv.h
+++ b/config/examples/BIQU/B1/Configuration_adv.h
@@ -2092,10 +2092,10 @@
   #define FILAMENT_CHANGE_ALERT_BEEPS         10  // Number of alert beeps to play when a response is needed.
   #define PAUSE_PARK_NO_STEPPER_TIMEOUT           // Enable for XYZ steppers to stay powered on during filament change.
 
-  #define PARK_HEAD_ON_PAUSE                    // Park the nozzle during pause and filament change.
-  #define HOME_BEFORE_FILAMENT_CHANGE           // If needed, home before parking for filament change
+  #define PARK_HEAD_ON_PAUSE                      // Park the nozzle during pause and filament change.
+  #define HOME_BEFORE_FILAMENT_CHANGE             // If needed, home before parking for filament change
 
-  #define FILAMENT_LOAD_UNLOAD_GCODES           // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
+  #define FILAMENT_LOAD_UNLOAD_GCODES             // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
   //#define FILAMENT_UNLOAD_ALL_EXTRUDERS         // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
 #endif