diff --git a/config/default/Configuration_adv.h b/config/default/Configuration_adv.h index bd913c903e..f8f0a29a89 100644 --- a/config/default/Configuration_adv.h +++ b/config/default/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h index 79d7f25568..e31aa8e681 100644 --- a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h +++ b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/ADIMLab/Gantry v1/Configuration_adv.h b/config/examples/ADIMLab/Gantry v1/Configuration_adv.h index 8822d902b6..422ecf3000 100644 --- a/config/examples/ADIMLab/Gantry v1/Configuration_adv.h +++ b/config/examples/ADIMLab/Gantry v1/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 28 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/ADIMLab/Gantry v2/Configuration_adv.h b/config/examples/ADIMLab/Gantry v2/Configuration_adv.h index a67b0ee74e..be140ef5f5 100644 --- a/config/examples/ADIMLab/Gantry v2/Configuration_adv.h +++ b/config/examples/ADIMLab/Gantry v2/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/AlephObjects/TAZ4/Configuration_adv.h b/config/examples/AlephObjects/TAZ4/Configuration_adv.h index 3675a38f8b..fb8d2175fa 100644 --- a/config/examples/AlephObjects/TAZ4/Configuration_adv.h +++ b/config/examples/AlephObjects/TAZ4/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Alfawise/U20-bltouch/Configuration_adv.h b/config/examples/Alfawise/U20-bltouch/Configuration_adv.h index f48108ac4c..090ceeaef7 100644 --- a/config/examples/Alfawise/U20-bltouch/Configuration_adv.h +++ b/config/examples/Alfawise/U20-bltouch/Configuration_adv.h @@ -1171,6 +1171,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Alfawise/U20/Configuration_adv.h b/config/examples/Alfawise/U20/Configuration_adv.h index 516d667882..7f64a2ca23 100644 --- a/config/examples/Alfawise/U20/Configuration_adv.h +++ b/config/examples/Alfawise/U20/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/AliExpress/UM2pExt/Configuration_adv.h b/config/examples/AliExpress/UM2pExt/Configuration_adv.h index f5197ac88b..26ea2656fe 100644 --- a/config/examples/AliExpress/UM2pExt/Configuration_adv.h +++ b/config/examples/AliExpress/UM2pExt/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Anet/A2/Configuration_adv.h b/config/examples/Anet/A2/Configuration_adv.h index 57ff7cf457..c1a2f6a80f 100644 --- a/config/examples/Anet/A2/Configuration_adv.h +++ b/config/examples/Anet/A2/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Anet/A2plus/Configuration_adv.h b/config/examples/Anet/A2plus/Configuration_adv.h index 57ff7cf457..c1a2f6a80f 100644 --- a/config/examples/Anet/A2plus/Configuration_adv.h +++ b/config/examples/Anet/A2plus/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Anet/A6/Configuration_adv.h b/config/examples/Anet/A6/Configuration_adv.h index ea093d1bc2..55510b8b72 100644 --- a/config/examples/Anet/A6/Configuration_adv.h +++ b/config/examples/Anet/A6/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Anet/A8/Configuration_adv.h b/config/examples/Anet/A8/Configuration_adv.h index bef34b2581..028a36599c 100644 --- a/config/examples/Anet/A8/Configuration_adv.h +++ b/config/examples/Anet/A8/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Anet/A8plus/Configuration_adv.h b/config/examples/Anet/A8plus/Configuration_adv.h index 06658b0aca..0f0c503607 100644 --- a/config/examples/Anet/A8plus/Configuration_adv.h +++ b/config/examples/Anet/A8plus/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Anet/E10/Configuration_adv.h b/config/examples/Anet/E10/Configuration_adv.h index 930a99c4f5..260bebe992 100644 --- a/config/examples/Anet/E10/Configuration_adv.h +++ b/config/examples/Anet/E10/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Anet/E16/Configuration_adv.h b/config/examples/Anet/E16/Configuration_adv.h index 7765a15f58..24b808ff9c 100644 --- a/config/examples/Anet/E16/Configuration_adv.h +++ b/config/examples/Anet/E16/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Anet/ET4/Configuration_adv.h b/config/examples/Anet/ET4/Configuration_adv.h index d95866f746..e8315f9db2 100644 --- a/config/examples/Anet/ET4/Configuration_adv.h +++ b/config/examples/Anet/ET4/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss diff --git a/config/examples/AnyCubic/Mega Zero/Configuration_adv.h b/config/examples/AnyCubic/Mega Zero/Configuration_adv.h index 7347a4bcd4..b1b67c9855 100644 --- a/config/examples/AnyCubic/Mega Zero/Configuration_adv.h +++ b/config/examples/AnyCubic/Mega Zero/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/AnyCubic/i3 Mega/Configuration_adv.h b/config/examples/AnyCubic/i3 Mega/Configuration_adv.h index 1b42162cba..f0db0a2a32 100644 --- a/config/examples/AnyCubic/i3 Mega/Configuration_adv.h +++ b/config/examples/AnyCubic/i3 Mega/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/AnyCubic/i3/Configuration_adv.h b/config/examples/AnyCubic/i3/Configuration_adv.h index 7787f630a8..ee3ca98e7b 100644 --- a/config/examples/AnyCubic/i3/Configuration_adv.h +++ b/config/examples/AnyCubic/i3/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/ArmEd/Configuration_adv.h b/config/examples/ArmEd/Configuration_adv.h index 85ea719ea5..8e0860d81f 100644 --- a/config/examples/ArmEd/Configuration_adv.h +++ b/config/examples/ArmEd/Configuration_adv.h @@ -1174,6 +1174,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Artillery/Genius/Configuration_adv.h b/config/examples/Artillery/Genius/Configuration_adv.h index 4bb48f1ce9..1a0dd22887 100644 --- a/config/examples/Artillery/Genius/Configuration_adv.h +++ b/config/examples/Artillery/Genius/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Artillery/Sidewinder X1/Configuration_adv.h b/config/examples/Artillery/Sidewinder X1/Configuration_adv.h index 4bb48f1ce9..1a0dd22887 100644 --- a/config/examples/Artillery/Sidewinder X1/Configuration_adv.h +++ b/config/examples/Artillery/Sidewinder X1/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Artillery/Sidewinder X1_0.9_degree_BMG_E3D_V6/Configuration_adv.h b/config/examples/Artillery/Sidewinder X1_0.9_degree_BMG_E3D_V6/Configuration_adv.h index 69fc2ce35a..8ee3d5bf6e 100644 --- a/config/examples/Artillery/Sidewinder X1_0.9_degree_BMG_E3D_V6/Configuration_adv.h +++ b/config/examples/Artillery/Sidewinder X1_0.9_degree_BMG_E3D_V6/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h index 3cd5511841..476f4924be 100644 --- a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h +++ b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/BIBO/TouchX/default/Configuration_adv.h b/config/examples/BIBO/TouchX/default/Configuration_adv.h index 8ef9300956..7507c19283 100644 --- a/config/examples/BIBO/TouchX/default/Configuration_adv.h +++ b/config/examples/BIBO/TouchX/default/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/BIQU/B1-BLTouch/Configuration_adv.h b/config/examples/BIQU/B1-BLTouch/Configuration_adv.h index 57c88b7776..0be71b5f97 100644 --- a/config/examples/BIQU/B1-BLTouch/Configuration_adv.h +++ b/config/examples/BIQU/B1-BLTouch/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/BIQU/B1/Configuration_adv.h b/config/examples/BIQU/B1/Configuration_adv.h index 4687644cbb..386d4ad205 100644 --- a/config/examples/BIQU/B1/Configuration_adv.h +++ b/config/examples/BIQU/B1/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/BQ/Hephestos/Configuration_adv.h b/config/examples/BQ/Hephestos/Configuration_adv.h index 1d817ddd30..c0c5b4254c 100644 --- a/config/examples/BQ/Hephestos/Configuration_adv.h +++ b/config/examples/BQ/Hephestos/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/BQ/Hephestos_2/Configuration_adv.h b/config/examples/BQ/Hephestos_2/Configuration_adv.h index d3ee657c7e..c8c8317756 100644 --- a/config/examples/BQ/Hephestos_2/Configuration_adv.h +++ b/config/examples/BQ/Hephestos_2/Configuration_adv.h @@ -1178,6 +1178,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/BQ/WITBOX/Configuration_adv.h b/config/examples/BQ/WITBOX/Configuration_adv.h index 1d817ddd30..c0c5b4254c 100644 --- a/config/examples/BQ/WITBOX/Configuration_adv.h +++ b/config/examples/BQ/WITBOX/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Cartesio/Configuration_adv.h b/config/examples/Cartesio/Configuration_adv.h index 1ff4a11a55..2a9bb99405 100644 --- a/config/examples/Cartesio/Configuration_adv.h +++ b/config/examples/Cartesio/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/CR-10 V2/Configuration_adv.h b/config/examples/Creality/CR-10 V2/Configuration_adv.h index 0272a8556b..d8c9c542cb 100644 --- a/config/examples/Creality/CR-10 V2/Configuration_adv.h +++ b/config/examples/Creality/CR-10 V2/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/CR-10/Configuration_adv.h b/config/examples/Creality/CR-10/Configuration_adv.h index 6e43702dbd..6a0a45ac05 100644 --- a/config/examples/Creality/CR-10/Configuration_adv.h +++ b/config/examples/Creality/CR-10/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/CR-10S/Configuration_adv.h b/config/examples/Creality/CR-10S/Configuration_adv.h index 17c130f06b..d188e22185 100644 --- a/config/examples/Creality/CR-10S/Configuration_adv.h +++ b/config/examples/Creality/CR-10S/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/CR-10_5S/Configuration_adv.h b/config/examples/Creality/CR-10_5S/Configuration_adv.h index d9fe9d29f6..d0658937b6 100644 --- a/config/examples/Creality/CR-10_5S/Configuration_adv.h +++ b/config/examples/Creality/CR-10_5S/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/CR-10mini/CrealityV1/Configuration_adv.h b/config/examples/Creality/CR-10mini/CrealityV1/Configuration_adv.h index 63afdf521f..ded6865a69 100644 --- a/config/examples/Creality/CR-10mini/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/CR-10mini/CrealityV1/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/CR-10mini/MEEB-3DP/Configuration_adv.h b/config/examples/Creality/CR-10mini/MEEB-3DP/Configuration_adv.h index 7f412482b3..d539248ddc 100644 --- a/config/examples/Creality/CR-10mini/MEEB-3DP/Configuration_adv.h +++ b/config/examples/Creality/CR-10mini/MEEB-3DP/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/CR-20 Pro/Configuration_adv.h b/config/examples/Creality/CR-20 Pro/Configuration_adv.h index fa8e56ba81..68e2fcc1ce 100644 --- a/config/examples/Creality/CR-20 Pro/Configuration_adv.h +++ b/config/examples/Creality/CR-20 Pro/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/CR-20/Configuration_adv.h b/config/examples/Creality/CR-20/Configuration_adv.h index 6a5de15d92..d9ec1a902c 100644 --- a/config/examples/Creality/CR-20/Configuration_adv.h +++ b/config/examples/Creality/CR-20/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/CR-8/Configuration_adv.h b/config/examples/Creality/CR-8/Configuration_adv.h index a9de3594ad..1d2828fcd7 100644 --- a/config/examples/Creality/CR-8/Configuration_adv.h +++ b/config/examples/Creality/CR-8/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/Ender-2/Configuration_adv.h b/config/examples/Creality/Ender-2/Configuration_adv.h index cb66370fc0..0d3b1ff6e3 100644 --- a/config/examples/Creality/Ender-2/Configuration_adv.h +++ b/config/examples/Creality/Ender-2/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/Ender-3 Pro V1.5/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro V1.5/Configuration_adv.h index 2e7511a65e..311fb0e133 100644 --- a/config/examples/Creality/Ender-3 Pro V1.5/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Pro V1.5/Configuration_adv.h @@ -1171,6 +1171,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h index 4e0179a5ca..5206a522bd 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h index ac57560862..6c1ab48354 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h index c7e6fb0c87..8ac5e33dde 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration_adv.h index de8a8a2119..f67e4ba086 100644 --- a/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/Ender-3 V2/Configuration_adv.h b/config/examples/Creality/Ender-3 V2/Configuration_adv.h index 2e95423e96..70be725d40 100644 --- a/config/examples/Creality/Ender-3 V2/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 V2/Configuration_adv.h @@ -1171,6 +1171,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h index 85005e3cd6..233d7b9180 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h index f95623cedf..7a16741020 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h index 8a336876f8..2e751018db 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/Ender-3/CrealityV1/Configuration_adv.h b/config/examples/Creality/Ender-3/CrealityV1/Configuration_adv.h index bff67df267..be25ef5b8a 100644 --- a/config/examples/Creality/Ender-3/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/CrealityV1/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration_adv.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration_adv.h index bb995952d1..8f35bad486 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration_adv.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration_adv.h index bb995952d1..8f35bad486 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration_adv.h b/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration_adv.h index bb995952d1..8f35bad486 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration_adv.h b/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration_adv.h index bb995952d1..8f35bad486 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/Ender-3/MEEB-3DP/Configuration_adv.h b/config/examples/Creality/Ender-3/MEEB-3DP/Configuration_adv.h index db536fa68d..0c4f86c15b 100644 --- a/config/examples/Creality/Ender-3/MEEB-3DP/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/MEEB-3DP/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/Ender-3/MKS Robin E3 1.0/Configuration_adv.h b/config/examples/Creality/Ender-3/MKS Robin E3 1.0/Configuration_adv.h index 70bcd1625a..83fa7c21d3 100644 --- a/config/examples/Creality/Ender-3/MKS Robin E3 1.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/MKS Robin E3 1.0/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/Ender-4/Configuration_adv.h b/config/examples/Creality/Ender-4/Configuration_adv.h index 41fd30b46b..b08dbe384e 100644 --- a/config/examples/Creality/Ender-4/Configuration_adv.h +++ b/config/examples/Creality/Ender-4/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/Ender-5 Pro/Configuration_adv.h b/config/examples/Creality/Ender-5 Pro/Configuration_adv.h index 686b3c63e0..4d61da617e 100644 --- a/config/examples/Creality/Ender-5 Pro/Configuration_adv.h +++ b/config/examples/Creality/Ender-5 Pro/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration_adv.h b/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration_adv.h index 208d25b75c..2f46f691d1 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration_adv.h @@ -1174,6 +1174,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h index 7eeab758d7..e24695446a 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/Ender-5/Creality/Configuration_adv.h b/config/examples/Creality/Ender-5/Creality/Configuration_adv.h index a12545443e..c41e317625 100644 --- a/config/examples/Creality/Ender-5/Creality/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/Creality/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Creality/Ender-5_Plus/Configuration_adv.h b/config/examples/Creality/Ender-5_Plus/Configuration_adv.h index e3f2adad1c..208952d2d6 100644 --- a/config/examples/Creality/Ender-5_Plus/Configuration_adv.h +++ b/config/examples/Creality/Ender-5_Plus/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h index 6e62ec05b2..b43fa95486 100644 --- a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h +++ b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Daycom/3DP-100/Configuration_adv.h b/config/examples/Daycom/3DP-100/Configuration_adv.h index 5c1b8d0c20..bc482514c6 100644 --- a/config/examples/Daycom/3DP-100/Configuration_adv.h +++ b/config/examples/Daycom/3DP-100/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h b/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h index f8eda7ab80..4516a987bb 100644 --- a/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h +++ b/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Einstart-S/Configuration_adv.h b/config/examples/Einstart-S/Configuration_adv.h index cd1dd45b32..1f9c28dd18 100644 --- a/config/examples/Einstart-S/Configuration_adv.h +++ b/config/examples/Einstart-S/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/FYSETC/AIO_II/Configuration_adv.h b/config/examples/FYSETC/AIO_II/Configuration_adv.h index fe06202f13..f27cf0bb05 100644 --- a/config/examples/FYSETC/AIO_II/Configuration_adv.h +++ b/config/examples/FYSETC/AIO_II/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/FYSETC/F6_13/Configuration_adv.h b/config/examples/FYSETC/F6_13/Configuration_adv.h index 096746122e..eb9f993364 100644 --- a/config/examples/FYSETC/F6_13/Configuration_adv.h +++ b/config/examples/FYSETC/F6_13/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/FYSETC/S6/Configuration_adv.h b/config/examples/FYSETC/S6/Configuration_adv.h index e9b30f8e81..68cea3f56f 100644 --- a/config/examples/FYSETC/S6/Configuration_adv.h +++ b/config/examples/FYSETC/S6/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Felix/DUAL/Configuration_adv.h b/config/examples/Felix/DUAL/Configuration_adv.h index b1b6b5eb10..bf69ebbb0f 100644 --- a/config/examples/Felix/DUAL/Configuration_adv.h +++ b/config/examples/Felix/DUAL/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Felix/Single/Configuration_adv.h b/config/examples/Felix/Single/Configuration_adv.h index b1b6b5eb10..bf69ebbb0f 100644 --- a/config/examples/Felix/Single/Configuration_adv.h +++ b/config/examples/Felix/Single/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/FlashForge/Creator 2X/Configuration_adv.h b/config/examples/FlashForge/Creator 2X/Configuration_adv.h index 25554765c3..4fc487cee6 100644 --- a/config/examples/FlashForge/Creator 2X/Configuration_adv.h +++ b/config/examples/FlashForge/Creator 2X/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/FlashForge/CreatorPro/Configuration_adv.h b/config/examples/FlashForge/CreatorPro/Configuration_adv.h index 339f1bb461..a6f475bc4b 100644 --- a/config/examples/FlashForge/CreatorPro/Configuration_adv.h +++ b/config/examples/FlashForge/CreatorPro/Configuration_adv.h @@ -1169,6 +1169,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/FlyingBear/P905H/Configuration_adv.h b/config/examples/FlyingBear/P905H/Configuration_adv.h index 37dfc0f2c4..8f38595c8b 100644 --- a/config/examples/FlyingBear/P905H/Configuration_adv.h +++ b/config/examples/FlyingBear/P905H/Configuration_adv.h @@ -1174,6 +1174,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/FolgerTech/i3-2020/Configuration_adv.h b/config/examples/FolgerTech/i3-2020/Configuration_adv.h index 1fa8a71446..69215ada8b 100644 --- a/config/examples/FolgerTech/i3-2020/Configuration_adv.h +++ b/config/examples/FolgerTech/i3-2020/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Formbot/Raptor/Configuration_adv.h b/config/examples/Formbot/Raptor/Configuration_adv.h index 81739a6d06..9ca0ac38db 100644 --- a/config/examples/Formbot/Raptor/Configuration_adv.h +++ b/config/examples/Formbot/Raptor/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h index 20f7db33db..8753086d03 100644 --- a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h +++ b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h @@ -1171,6 +1171,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Formbot/T_Rex_3/Configuration_adv.h b/config/examples/Formbot/T_Rex_3/Configuration_adv.h index 494f3049f7..3e8435b977 100644 --- a/config/examples/Formbot/T_Rex_3/Configuration_adv.h +++ b/config/examples/Formbot/T_Rex_3/Configuration_adv.h @@ -1175,6 +1175,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Geeetech/A10/Configuration_adv.h b/config/examples/Geeetech/A10/Configuration_adv.h index 0602c7378c..48eeb15944 100644 --- a/config/examples/Geeetech/A10/Configuration_adv.h +++ b/config/examples/Geeetech/A10/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Geeetech/A10D/Configuration_adv.h b/config/examples/Geeetech/A10D/Configuration_adv.h index 0801408cac..a7443bf4f0 100644 --- a/config/examples/Geeetech/A10D/Configuration_adv.h +++ b/config/examples/Geeetech/A10D/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Geeetech/A10M/Configuration_adv.h b/config/examples/Geeetech/A10M/Configuration_adv.h index 8eb7e51985..8050d45005 100644 --- a/config/examples/Geeetech/A10M/Configuration_adv.h +++ b/config/examples/Geeetech/A10M/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) #define POWER_LOSS_PIN 69 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss diff --git a/config/examples/Geeetech/A10T/Configuration_adv.h b/config/examples/Geeetech/A10T/Configuration_adv.h index 8eb7e51985..8050d45005 100644 --- a/config/examples/Geeetech/A10T/Configuration_adv.h +++ b/config/examples/Geeetech/A10T/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) #define POWER_LOSS_PIN 69 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss diff --git a/config/examples/Geeetech/A20/Configuration_adv.h b/config/examples/Geeetech/A20/Configuration_adv.h index c92d08ee17..881fc4271d 100644 --- a/config/examples/Geeetech/A20/Configuration_adv.h +++ b/config/examples/Geeetech/A20/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) #define POWER_LOSS_PIN 69 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss diff --git a/config/examples/Geeetech/A20M/Configuration_adv.h b/config/examples/Geeetech/A20M/Configuration_adv.h index c92d08ee17..881fc4271d 100644 --- a/config/examples/Geeetech/A20M/Configuration_adv.h +++ b/config/examples/Geeetech/A20M/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) #define POWER_LOSS_PIN 69 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss diff --git a/config/examples/Geeetech/A20T/Configuration_adv.h b/config/examples/Geeetech/A20T/Configuration_adv.h index c92d08ee17..881fc4271d 100644 --- a/config/examples/Geeetech/A20T/Configuration_adv.h +++ b/config/examples/Geeetech/A20T/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) #define POWER_LOSS_PIN 69 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss diff --git a/config/examples/Geeetech/A30/Configuration_adv.h b/config/examples/Geeetech/A30/Configuration_adv.h index 2589cd8312..cb4345838f 100644 --- a/config/examples/Geeetech/A30/Configuration_adv.h +++ b/config/examples/Geeetech/A30/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Geeetech/D200/Configuration_adv.h b/config/examples/Geeetech/D200/Configuration_adv.h index 05ade1500f..c09cd0d7a9 100644 --- a/config/examples/Geeetech/D200/Configuration_adv.h +++ b/config/examples/Geeetech/D200/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Geeetech/Duplicator5/Configuration_adv.h b/config/examples/Geeetech/Duplicator5/Configuration_adv.h index e9b30f8e81..68cea3f56f 100644 --- a/config/examples/Geeetech/Duplicator5/Configuration_adv.h +++ b/config/examples/Geeetech/Duplicator5/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Geeetech/E180/Configuration_adv.h b/config/examples/Geeetech/E180/Configuration_adv.h index 2589cd8312..cb4345838f 100644 --- a/config/examples/Geeetech/E180/Configuration_adv.h +++ b/config/examples/Geeetech/E180/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Geeetech/M201/Configuration_adv.h b/config/examples/Geeetech/M201/Configuration_adv.h index 05ade1500f..c09cd0d7a9 100644 --- a/config/examples/Geeetech/M201/Configuration_adv.h +++ b/config/examples/Geeetech/M201/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Geeetech/MeCreator2/Configuration_adv.h b/config/examples/Geeetech/MeCreator2/Configuration_adv.h index 7d2fc032af..55081963f3 100644 --- a/config/examples/Geeetech/MeCreator2/Configuration_adv.h +++ b/config/examples/Geeetech/MeCreator2/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Geeetech/Me_creator/Configuration_adv.h b/config/examples/Geeetech/Me_creator/Configuration_adv.h index e9b30f8e81..68cea3f56f 100644 --- a/config/examples/Geeetech/Me_creator/Configuration_adv.h +++ b/config/examples/Geeetech/Me_creator/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Geeetech/Me_ducer/Configuration_adv.h b/config/examples/Geeetech/Me_ducer/Configuration_adv.h index e9b30f8e81..68cea3f56f 100644 --- a/config/examples/Geeetech/Me_ducer/Configuration_adv.h +++ b/config/examples/Geeetech/Me_ducer/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Geeetech/PI3A PRO/Configuration_adv.h b/config/examples/Geeetech/PI3A PRO/Configuration_adv.h index 7f52c8ec8d..cfbc51dfd2 100644 --- a/config/examples/Geeetech/PI3A PRO/Configuration_adv.h +++ b/config/examples/Geeetech/PI3A PRO/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h index 0602c7378c..48eeb15944 100644 --- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h +++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h index 0602c7378c..48eeb15944 100644 --- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h +++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/HMS434/Configuration_adv.h b/config/examples/HMS434/Configuration_adv.h index d01200a8c0..6d54679cbd 100644 --- a/config/examples/HMS434/Configuration_adv.h +++ b/config/examples/HMS434/Configuration_adv.h @@ -1161,6 +1161,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Infitary/i3-M508/Configuration_adv.h b/config/examples/Infitary/i3-M508/Configuration_adv.h index 8eee196c7e..4d39f32d30 100644 --- a/config/examples/Infitary/i3-M508/Configuration_adv.h +++ b/config/examples/Infitary/i3-M508/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Intamsys/FunmatHT_4988/Configuration_adv.h b/config/examples/Intamsys/FunmatHT_4988/Configuration_adv.h index 698f2c1b46..51c544c128 100644 --- a/config/examples/Intamsys/FunmatHT_4988/Configuration_adv.h +++ b/config/examples/Intamsys/FunmatHT_4988/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/JGAurora/A1/Configuration_adv.h b/config/examples/JGAurora/A1/Configuration_adv.h index af243b592c..f80e646677 100644 --- a/config/examples/JGAurora/A1/Configuration_adv.h +++ b/config/examples/JGAurora/A1/Configuration_adv.h @@ -1175,6 +1175,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/JGAurora/A5/Configuration_adv.h b/config/examples/JGAurora/A5/Configuration_adv.h index 575c18bd32..83629c3b2b 100644 --- a/config/examples/JGAurora/A5/Configuration_adv.h +++ b/config/examples/JGAurora/A5/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/JGAurora/A5S/Configuration_adv.h b/config/examples/JGAurora/A5S/Configuration_adv.h index af243b592c..f80e646677 100644 --- a/config/examples/JGAurora/A5S/Configuration_adv.h +++ b/config/examples/JGAurora/A5S/Configuration_adv.h @@ -1175,6 +1175,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/JGAurora/Magic/Configuration_adv.h b/config/examples/JGAurora/Magic/Configuration_adv.h index 4ba581e401..74a2e7cf2c 100644 --- a/config/examples/JGAurora/Magic/Configuration_adv.h +++ b/config/examples/JGAurora/Magic/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Kingroon/KP3/Configuration_adv.h b/config/examples/Kingroon/KP3/Configuration_adv.h index 00f96fdc28..83f23614c7 100644 --- a/config/examples/Kingroon/KP3/Configuration_adv.h +++ b/config/examples/Kingroon/KP3/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/MBot/Cube/Configuration_adv.h b/config/examples/MBot/Cube/Configuration_adv.h index bc20760ae8..87dcf39727 100644 --- a/config/examples/MBot/Cube/Configuration_adv.h +++ b/config/examples/MBot/Cube/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/MakerFarm/Pegasus_12/Configuration_adv.h b/config/examples/MakerFarm/Pegasus_12/Configuration_adv.h index 84b603e081..8fbc773667 100644 --- a/config/examples/MakerFarm/Pegasus_12/Configuration_adv.h +++ b/config/examples/MakerFarm/Pegasus_12/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/MakerParts/Configuration_adv.h b/config/examples/MakerParts/Configuration_adv.h index cb033edd67..4253ff9913 100644 --- a/config/examples/MakerParts/Configuration_adv.h +++ b/config/examples/MakerParts/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Malyan/M150/Configuration_adv.h b/config/examples/Malyan/M150/Configuration_adv.h index 3cdaba3378..da49d6b3bb 100644 --- a/config/examples/Malyan/M150/Configuration_adv.h +++ b/config/examples/Malyan/M150/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Malyan/M200/Configuration_adv.h b/config/examples/Malyan/M200/Configuration_adv.h index eb6e62bf1b..1fbd57cb0a 100644 --- a/config/examples/Malyan/M200/Configuration_adv.h +++ b/config/examples/Malyan/M200/Configuration_adv.h @@ -1172,6 +1172,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Micromake/C1/enhanced/Configuration_adv.h b/config/examples/Micromake/C1/enhanced/Configuration_adv.h index 14367fbcac..e69bb6dd1a 100644 --- a/config/examples/Micromake/C1/enhanced/Configuration_adv.h +++ b/config/examples/Micromake/C1/enhanced/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Mks/Robin/Configuration_adv.h b/config/examples/Mks/Robin/Configuration_adv.h index bd913c903e..f8f0a29a89 100644 --- a/config/examples/Mks/Robin/Configuration_adv.h +++ b/config/examples/Mks/Robin/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Mks/Sbase/Configuration_adv.h b/config/examples/Mks/Sbase/Configuration_adv.h index a9904068b2..55a651c893 100644 --- a/config/examples/Mks/Sbase/Configuration_adv.h +++ b/config/examples/Mks/Sbase/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Modix/Big60/Configuration_adv.h b/config/examples/Modix/Big60/Configuration_adv.h index 28992d5637..85bf83a9cd 100644 --- a/config/examples/Modix/Big60/Configuration_adv.h +++ b/config/examples/Modix/Big60/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Ortur 4/Configuration_adv.h b/config/examples/Ortur 4/Configuration_adv.h index bd9961a623..72c8e5eeba 100644 --- a/config/examples/Ortur 4/Configuration_adv.h +++ b/config/examples/Ortur 4/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) #define POWER_LOSS_PIN 64 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss diff --git a/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration_adv.h b/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration_adv.h index cf2607480c..7420a67ea4 100644 --- a/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration_adv.h +++ b/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss diff --git a/config/examples/Qidi/Qidi 1/Configuration_adv.h b/config/examples/Qidi/Qidi 1/Configuration_adv.h index 92a37af4a6..8ad3edf8af 100644 --- a/config/examples/Qidi/Qidi 1/Configuration_adv.h +++ b/config/examples/Qidi/Qidi 1/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/RapideLite/RL200/Configuration_adv.h b/config/examples/RapideLite/RL200/Configuration_adv.h index dd5bac39ce..3155123512 100644 --- a/config/examples/RapideLite/RL200/Configuration_adv.h +++ b/config/examples/RapideLite/RL200/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Renkforce/RF100/Configuration_adv.h b/config/examples/Renkforce/RF100/Configuration_adv.h index 25907a4118..3c755310da 100644 --- a/config/examples/Renkforce/RF100/Configuration_adv.h +++ b/config/examples/Renkforce/RF100/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Renkforce/RF100XL/Configuration_adv.h b/config/examples/Renkforce/RF100XL/Configuration_adv.h index 25907a4118..3c755310da 100644 --- a/config/examples/Renkforce/RF100XL/Configuration_adv.h +++ b/config/examples/Renkforce/RF100XL/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Renkforce/RF100v2/Configuration_adv.h b/config/examples/Renkforce/RF100v2/Configuration_adv.h index 25907a4118..3c755310da 100644 --- a/config/examples/Renkforce/RF100v2/Configuration_adv.h +++ b/config/examples/Renkforce/RF100v2/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/RigidBot/Configuration_adv.h b/config/examples/RigidBot/Configuration_adv.h index 93fe1bb570..6559158782 100644 --- a/config/examples/RigidBot/Configuration_adv.h +++ b/config/examples/RigidBot/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/SCARA/MP_SCARA/Configuration_adv.h b/config/examples/SCARA/MP_SCARA/Configuration_adv.h index c96f642e1d..1beaf583f2 100644 --- a/config/examples/SCARA/MP_SCARA/Configuration_adv.h +++ b/config/examples/SCARA/MP_SCARA/Configuration_adv.h @@ -1167,6 +1167,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/SCARA/Morgan/Configuration_adv.h b/config/examples/SCARA/Morgan/Configuration_adv.h index 771d31d137..0f2ff2e7c2 100644 --- a/config/examples/SCARA/Morgan/Configuration_adv.h +++ b/config/examples/SCARA/Morgan/Configuration_adv.h @@ -1167,6 +1167,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h index 1a908ffb8b..55a46db8d0 100644 --- a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h +++ b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Sanguinololu/Configuration_adv.h b/config/examples/Sanguinololu/Configuration_adv.h index bd6b26453d..f1c20e0189 100644 --- a/config/examples/Sanguinololu/Configuration_adv.h +++ b/config/examples/Sanguinololu/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Sovol/SV-01/Configuration_adv.h b/config/examples/Sovol/SV-01/Configuration_adv.h index 0452cefe6e..29bb7703c7 100644 --- a/config/examples/Sovol/SV-01/Configuration_adv.h +++ b/config/examples/Sovol/SV-01/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE LOW // State of pin indicating power loss diff --git a/config/examples/Tevo/Michelangelo/Configuration_adv.h b/config/examples/Tevo/Michelangelo/Configuration_adv.h index 2c7a1e187a..5e51efe13c 100644 --- a/config/examples/Tevo/Michelangelo/Configuration_adv.h +++ b/config/examples/Tevo/Michelangelo/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Tevo/Nereus/Configuration_adv.h b/config/examples/Tevo/Nereus/Configuration_adv.h index 8b99da245c..2594c03700 100644 --- a/config/examples/Tevo/Nereus/Configuration_adv.h +++ b/config/examples/Tevo/Nereus/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Tevo/Tarantula Pro/Configuration_adv.h b/config/examples/Tevo/Tarantula Pro/Configuration_adv.h index 112ba740eb..2c671d09e3 100644 --- a/config/examples/Tevo/Tarantula Pro/Configuration_adv.h +++ b/config/examples/Tevo/Tarantula Pro/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h index 0d1704922a..13ca90ca3c 100644 --- a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h +++ b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h index 0d1704922a..13ca90ca3c 100644 --- a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h +++ b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/TheBorg/Configuration_adv.h b/config/examples/TheBorg/Configuration_adv.h index d2a55f1d91..4781c07ef4 100644 --- a/config/examples/TheBorg/Configuration_adv.h +++ b/config/examples/TheBorg/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/TinyBoy2/Configuration_adv.h b/config/examples/TinyBoy2/Configuration_adv.h index e163837826..728c12ec92 100644 --- a/config/examples/TinyBoy2/Configuration_adv.h +++ b/config/examples/TinyBoy2/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Tronxy/X3A/Configuration_adv.h b/config/examples/Tronxy/X3A/Configuration_adv.h index c033806524..e72baf6004 100644 --- a/config/examples/Tronxy/X3A/Configuration_adv.h +++ b/config/examples/Tronxy/X3A/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Tronxy/X5S-2E/Configuration_adv.h b/config/examples/Tronxy/X5S-2E/Configuration_adv.h index e75cc62115..1d13d95b47 100644 --- a/config/examples/Tronxy/X5S-2E/Configuration_adv.h +++ b/config/examples/Tronxy/X5S-2E/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Tronxy/X5SA/Configuration_adv.h b/config/examples/Tronxy/X5SA/Configuration_adv.h index dea925a73f..760bcfad72 100644 --- a/config/examples/Tronxy/X5SA/Configuration_adv.h +++ b/config/examples/Tronxy/X5SA/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/UltiMachine/Archim1/Configuration_adv.h b/config/examples/UltiMachine/Archim1/Configuration_adv.h index 6bdc19dc83..ec74c1a5e7 100644 --- a/config/examples/UltiMachine/Archim1/Configuration_adv.h +++ b/config/examples/UltiMachine/Archim1/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/UltiMachine/Archim2/Configuration_adv.h b/config/examples/UltiMachine/Archim2/Configuration_adv.h index daba557eb2..6cf6e5b9a6 100644 --- a/config/examples/UltiMachine/Archim2/Configuration_adv.h +++ b/config/examples/UltiMachine/Archim2/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/VORONDesign/Configuration_adv.h b/config/examples/VORONDesign/Configuration_adv.h index ac462a7f96..fd4472dbf3 100644 --- a/config/examples/VORONDesign/Configuration_adv.h +++ b/config/examples/VORONDesign/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Velleman/K8200/Configuration_adv.h b/config/examples/Velleman/K8200/Configuration_adv.h index c078f0b1f7..1188e3fe25 100644 --- a/config/examples/Velleman/K8200/Configuration_adv.h +++ b/config/examples/Velleman/K8200/Configuration_adv.h @@ -1183,6 +1183,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h b/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h index 693791c739..3c07879f69 100644 --- a/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h +++ b/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Velleman/K8400/Single-head/Configuration_adv.h b/config/examples/Velleman/K8400/Single-head/Configuration_adv.h index 693791c739..3c07879f69 100644 --- a/config/examples/Velleman/K8400/Single-head/Configuration_adv.h +++ b/config/examples/Velleman/K8400/Single-head/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/WASP/PowerWASP/Configuration_adv.h b/config/examples/WASP/PowerWASP/Configuration_adv.h index 7b208f9fa4..8e76671caf 100644 --- a/config/examples/WASP/PowerWASP/Configuration_adv.h +++ b/config/examples/WASP/PowerWASP/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) #define POWER_LOSS_PIN 65 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss diff --git a/config/examples/Wanhao/Duplicator 4S/Configuration_adv.h b/config/examples/Wanhao/Duplicator 4S/Configuration_adv.h index 9c69f5f2df..f3d3659a3b 100644 --- a/config/examples/Wanhao/Duplicator 4S/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator 4S/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h index 654281b283..d0267f9131 100644 --- a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h @@ -1172,6 +1172,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h b/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h index ccb54c0d2b..4ee41a5ba5 100644 --- a/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h b/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h index dc9a72953d..c95b36c589 100644 --- a/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Weistek/wt150/Configuration_adv.h b/config/examples/Weistek/wt150/Configuration_adv.h index bdb4257657..4909c1d11d 100644 --- a/config/examples/Weistek/wt150/Configuration_adv.h +++ b/config/examples/Weistek/wt150/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Zonestar/P802M/Configuration_adv.h b/config/examples/Zonestar/P802M/Configuration_adv.h index 07c37c73de..b1d343539d 100644 --- a/config/examples/Zonestar/P802M/Configuration_adv.h +++ b/config/examples/Zonestar/P802M/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration_adv.h b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration_adv.h index c4bcab4bd5..984c4e44f2 100755 --- a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration_adv.h +++ b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration_adv.h @@ -1164,6 +1164,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration_adv.h b/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration_adv.h index 7ca2de1b86..c52dc978e8 100644 --- a/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration_adv.h +++ b/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration_adv.h @@ -1173,6 +1173,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h index 0d178e8b90..feaa21bdce 100644 --- a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h +++ b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h @@ -1172,6 +1172,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/delta/Anycubic/Predator/Configuration_adv.h b/config/examples/delta/Anycubic/Predator/Configuration_adv.h index 62a93b8887..e1261ed7a3 100644 --- a/config/examples/delta/Anycubic/Predator/Configuration_adv.h +++ b/config/examples/delta/Anycubic/Predator/Configuration_adv.h @@ -1173,6 +1173,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h b/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h index f79988132c..9af77fd53b 100644 --- a/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h +++ b/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h @@ -1172,6 +1172,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss diff --git a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h index e5055193f6..240e7ddc73 100644 --- a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h +++ b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h @@ -1172,6 +1172,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss diff --git a/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h b/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h index bb48d31c87..da45178b8b 100644 --- a/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h +++ b/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h @@ -1172,6 +1172,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h index 62e47c0319..1adbf81ac9 100644 --- a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h +++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h @@ -1172,6 +1172,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/delta/FLSUN/kossel/Configuration_adv.h b/config/examples/delta/FLSUN/kossel/Configuration_adv.h index 62e47c0319..1adbf81ac9 100644 --- a/config/examples/delta/FLSUN/kossel/Configuration_adv.h +++ b/config/examples/delta/FLSUN/kossel/Configuration_adv.h @@ -1172,6 +1172,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h index 4981c275b4..ea08c9392e 100644 --- a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h +++ b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h @@ -1172,6 +1172,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/delta/Geeetech/G2/Configuration_adv.h b/config/examples/delta/Geeetech/G2/Configuration_adv.h index f75ddebf10..04b6c446ed 100644 --- a/config/examples/delta/Geeetech/G2/Configuration_adv.h +++ b/config/examples/delta/Geeetech/G2/Configuration_adv.h @@ -1172,6 +1172,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/delta/Geeetech/G2Pro/Configuration_adv.h b/config/examples/delta/Geeetech/G2Pro/Configuration_adv.h index 40496941b2..c176faa09c 100644 --- a/config/examples/delta/Geeetech/G2Pro/Configuration_adv.h +++ b/config/examples/delta/Geeetech/G2Pro/Configuration_adv.h @@ -1172,6 +1172,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/delta/Geeetech/G2S/Configuration_adv.h b/config/examples/delta/Geeetech/G2S/Configuration_adv.h index 40496941b2..c176faa09c 100644 --- a/config/examples/delta/Geeetech/G2S/Configuration_adv.h +++ b/config/examples/delta/Geeetech/G2S/Configuration_adv.h @@ -1172,6 +1172,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/delta/Geeetech/G2SPro/Configuration_adv.h b/config/examples/delta/Geeetech/G2SPro/Configuration_adv.h index 40496941b2..c176faa09c 100644 --- a/config/examples/delta/Geeetech/G2SPro/Configuration_adv.h +++ b/config/examples/delta/Geeetech/G2SPro/Configuration_adv.h @@ -1172,6 +1172,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h index ce5143121d..a93b0b5870 100644 --- a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h +++ b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h @@ -1172,6 +1172,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/delta/Hatchbox_Alpha/Configuration_adv.h b/config/examples/delta/Hatchbox_Alpha/Configuration_adv.h index 4e970e5b4e..b74fa09739 100644 --- a/config/examples/delta/Hatchbox_Alpha/Configuration_adv.h +++ b/config/examples/delta/Hatchbox_Alpha/Configuration_adv.h @@ -1172,6 +1172,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/delta/MKS/SBASE/Configuration_adv.h b/config/examples/delta/MKS/SBASE/Configuration_adv.h index c4816a2f10..bef4d53501 100644 --- a/config/examples/delta/MKS/SBASE/Configuration_adv.h +++ b/config/examples/delta/MKS/SBASE/Configuration_adv.h @@ -1172,6 +1172,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/delta/Malyan M300/Configuration_adv.h b/config/examples/delta/Malyan M300/Configuration_adv.h index fc30aec774..622d5c1863 100644 --- a/config/examples/delta/Malyan M300/Configuration_adv.h +++ b/config/examples/delta/Malyan M300/Configuration_adv.h @@ -1172,6 +1172,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/delta/Tevo Little Monster/Configuration_adv.h b/config/examples/delta/Tevo Little Monster/Configuration_adv.h index cc1c5975e5..2a7ccdf212 100644 --- a/config/examples/delta/Tevo Little Monster/Configuration_adv.h +++ b/config/examples/delta/Tevo Little Monster/Configuration_adv.h @@ -1172,6 +1172,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/delta/generic/Configuration_adv.h b/config/examples/delta/generic/Configuration_adv.h index 4981c275b4..ea08c9392e 100644 --- a/config/examples/delta/generic/Configuration_adv.h +++ b/config/examples/delta/generic/Configuration_adv.h @@ -1172,6 +1172,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/delta/kossel_clear/Configuration_adv.h b/config/examples/delta/kossel_clear/Configuration_adv.h index 6817833cc4..504bc9d5c7 100644 --- a/config/examples/delta/kossel_clear/Configuration_adv.h +++ b/config/examples/delta/kossel_clear/Configuration_adv.h @@ -1172,6 +1172,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/delta/kossel_xl/Configuration_adv.h b/config/examples/delta/kossel_xl/Configuration_adv.h index b673e633ce..300543e26c 100644 --- a/config/examples/delta/kossel_xl/Configuration_adv.h +++ b/config/examples/delta/kossel_xl/Configuration_adv.h @@ -1172,6 +1172,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/gCreate/gMax1.5+/Configuration_adv.h b/config/examples/gCreate/gMax1.5+/Configuration_adv.h index f6ebbfe900..36a8a6d728 100644 --- a/config/examples/gCreate/gMax1.5+/Configuration_adv.h +++ b/config/examples/gCreate/gMax1.5+/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/makibox/Configuration_adv.h b/config/examples/makibox/Configuration_adv.h index 6899f0fb1c..ddae2ca97d 100644 --- a/config/examples/makibox/Configuration_adv.h +++ b/config/examples/makibox/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss diff --git a/config/examples/tvrrug/Round2/Configuration_adv.h b/config/examples/tvrrug/Round2/Configuration_adv.h index 78fa9a4081..818a1091a4 100644 --- a/config/examples/tvrrug/Round2/Configuration_adv.h +++ b/config/examples/tvrrug/Round2/Configuration_adv.h @@ -1170,6 +1170,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss + //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss