diff --git a/config/default/Configuration.h b/config/default/Configuration.h index d23b69c02b..39dc195231 100644 --- a/config/default/Configuration.h +++ b/config/default/Configuration.h @@ -2062,7 +2062,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2332,13 +2332,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2355,7 +2355,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2363,12 +2363,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/default/Configuration_adv.h b/config/default/Configuration_adv.h index 6f75cc38c7..19906819a1 100644 --- a/config/default/Configuration_adv.h +++ b/config/default/Configuration_adv.h @@ -488,7 +488,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/3DFabXYZ/Migbot/Configuration.h b/config/examples/3DFabXYZ/Migbot/Configuration.h index ac58dea4a3..64c20caf89 100644 --- a/config/examples/3DFabXYZ/Migbot/Configuration.h +++ b/config/examples/3DFabXYZ/Migbot/Configuration.h @@ -2096,7 +2096,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2366,13 +2366,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2389,7 +2389,7 @@ #define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2397,12 +2397,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h index 4ef3640bdc..be1db060d1 100644 --- a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h +++ b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm #define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/ADIMLab/Gantry v1/Configuration.h b/config/examples/ADIMLab/Gantry v1/Configuration.h index 6783e96982..19c0896071 100644 --- a/config/examples/ADIMLab/Gantry v1/Configuration.h +++ b/config/examples/ADIMLab/Gantry v1/Configuration.h @@ -2065,7 +2065,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2335,13 +2335,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2358,7 +2358,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2366,12 +2366,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/ADIMLab/Gantry v1/Configuration_adv.h b/config/examples/ADIMLab/Gantry v1/Configuration_adv.h index bc1bcb504d..b7d5e018fb 100644 --- a/config/examples/ADIMLab/Gantry v1/Configuration_adv.h +++ b/config/examples/ADIMLab/Gantry v1/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm #define CASE_LIGHT_MENU // Add Case Light options to the LCD menu #define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/ADIMLab/Gantry v2/Configuration.h b/config/examples/ADIMLab/Gantry v2/Configuration.h index b68fd0a596..1bc3cd7bdc 100644 --- a/config/examples/ADIMLab/Gantry v2/Configuration.h +++ b/config/examples/ADIMLab/Gantry v2/Configuration.h @@ -2065,7 +2065,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2335,13 +2335,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2358,7 +2358,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2366,12 +2366,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/ADIMLab/Gantry v2/Configuration_adv.h b/config/examples/ADIMLab/Gantry v2/Configuration_adv.h index 952e9dcee1..463235af3f 100644 --- a/config/examples/ADIMLab/Gantry v2/Configuration_adv.h +++ b/config/examples/ADIMLab/Gantry v2/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/AlephObjects/TAZ4/Configuration.h b/config/examples/AlephObjects/TAZ4/Configuration.h index d152415bb3..27c59582ae 100644 --- a/config/examples/AlephObjects/TAZ4/Configuration.h +++ b/config/examples/AlephObjects/TAZ4/Configuration.h @@ -2082,7 +2082,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2352,13 +2352,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2375,7 +2375,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2383,12 +2383,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/AlephObjects/TAZ4/Configuration_adv.h b/config/examples/AlephObjects/TAZ4/Configuration_adv.h index 018910f086..ce3de3b1e9 100644 --- a/config/examples/AlephObjects/TAZ4/Configuration_adv.h +++ b/config/examples/AlephObjects/TAZ4/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Alfawise/U20-bltouch/Configuration.h b/config/examples/Alfawise/U20-bltouch/Configuration.h index 41e758c06b..71231897ef 100644 --- a/config/examples/Alfawise/U20-bltouch/Configuration.h +++ b/config/examples/Alfawise/U20-bltouch/Configuration.h @@ -2143,7 +2143,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2432,13 +2432,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2455,7 +2455,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2463,12 +2463,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Alfawise/U20-bltouch/Configuration_adv.h b/config/examples/Alfawise/U20-bltouch/Configuration_adv.h index 8e7c66c171..82831f894d 100644 --- a/config/examples/Alfawise/U20-bltouch/Configuration_adv.h +++ b/config/examples/Alfawise/U20-bltouch/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Alfawise/U20/Configuration.h b/config/examples/Alfawise/U20/Configuration.h index 847e351abf..bbdaeb60bd 100644 --- a/config/examples/Alfawise/U20/Configuration.h +++ b/config/examples/Alfawise/U20/Configuration.h @@ -2143,7 +2143,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2432,13 +2432,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2455,7 +2455,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2463,12 +2463,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Alfawise/U20/Configuration_adv.h b/config/examples/Alfawise/U20/Configuration_adv.h index 8f5d2fed17..c3a73810c9 100644 --- a/config/examples/Alfawise/U20/Configuration_adv.h +++ b/config/examples/Alfawise/U20/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/AliExpress/CL-260/Configuration.h b/config/examples/AliExpress/CL-260/Configuration.h index 3f4b65112c..314331f8b7 100644 --- a/config/examples/AliExpress/CL-260/Configuration.h +++ b/config/examples/AliExpress/CL-260/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/AliExpress/UM2pExt/Configuration.h b/config/examples/AliExpress/UM2pExt/Configuration.h index 3cc19227c5..1fda549135 100644 --- a/config/examples/AliExpress/UM2pExt/Configuration.h +++ b/config/examples/AliExpress/UM2pExt/Configuration.h @@ -2075,7 +2075,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2345,13 +2345,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2368,7 +2368,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2376,12 +2376,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/AliExpress/UM2pExt/Configuration_adv.h b/config/examples/AliExpress/UM2pExt/Configuration_adv.h index aa362e760e..676d0ef358 100644 --- a/config/examples/AliExpress/UM2pExt/Configuration_adv.h +++ b/config/examples/AliExpress/UM2pExt/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm #define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Anet/A2/Configuration.h b/config/examples/Anet/A2/Configuration.h index 98ca4a8d21..d27540a7f4 100644 --- a/config/examples/Anet/A2/Configuration.h +++ b/config/examples/Anet/A2/Configuration.h @@ -2066,7 +2066,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2336,13 +2336,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2359,7 +2359,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2367,12 +2367,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Anet/A2/Configuration_adv.h b/config/examples/Anet/A2/Configuration_adv.h index 6fabc01199..cdb0cccb43 100644 --- a/config/examples/Anet/A2/Configuration_adv.h +++ b/config/examples/Anet/A2/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Anet/A2plus/Configuration.h b/config/examples/Anet/A2plus/Configuration.h index 08dba3a5fd..4f26596bb1 100644 --- a/config/examples/Anet/A2plus/Configuration.h +++ b/config/examples/Anet/A2plus/Configuration.h @@ -2066,7 +2066,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2336,13 +2336,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2359,7 +2359,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2367,12 +2367,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Anet/A2plus/Configuration_adv.h b/config/examples/Anet/A2plus/Configuration_adv.h index 8217cda506..0d8e280880 100644 --- a/config/examples/Anet/A2plus/Configuration_adv.h +++ b/config/examples/Anet/A2plus/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Anet/A6/Configuration.h b/config/examples/Anet/A6/Configuration.h index 606af3ade0..9d507632b1 100644 --- a/config/examples/Anet/A6/Configuration.h +++ b/config/examples/Anet/A6/Configuration.h @@ -2181,7 +2181,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2451,13 +2451,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2474,7 +2474,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2482,12 +2482,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Anet/A6/Configuration_adv.h b/config/examples/Anet/A6/Configuration_adv.h index 31dacadf81..3a89f28a59 100644 --- a/config/examples/Anet/A6/Configuration_adv.h +++ b/config/examples/Anet/A6/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Anet/A8/Configuration.h b/config/examples/Anet/A8/Configuration.h index 24ab2b00ae..78f8535706 100644 --- a/config/examples/Anet/A8/Configuration.h +++ b/config/examples/Anet/A8/Configuration.h @@ -2079,7 +2079,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2349,13 +2349,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2372,7 +2372,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2380,12 +2380,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Anet/A8/Configuration_adv.h b/config/examples/Anet/A8/Configuration_adv.h index f19c69341a..c7771155fb 100644 --- a/config/examples/Anet/A8/Configuration_adv.h +++ b/config/examples/Anet/A8/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Anet/A8plus/Configuration.h b/config/examples/Anet/A8plus/Configuration.h index 6973ade6c4..08981cc67e 100644 --- a/config/examples/Anet/A8plus/Configuration.h +++ b/config/examples/Anet/A8plus/Configuration.h @@ -2075,7 +2075,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2348,13 +2348,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2371,7 +2371,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2379,12 +2379,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Anet/A8plus/Configuration_adv.h b/config/examples/Anet/A8plus/Configuration_adv.h index 4dbf9886fe..614daf3dda 100644 --- a/config/examples/Anet/A8plus/Configuration_adv.h +++ b/config/examples/Anet/A8plus/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Anet/E10/Configuration.h b/config/examples/Anet/E10/Configuration.h index 45668c2361..c15d617703 100644 --- a/config/examples/Anet/E10/Configuration.h +++ b/config/examples/Anet/E10/Configuration.h @@ -2065,7 +2065,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2335,13 +2335,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2358,7 +2358,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2366,12 +2366,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Anet/E10/Configuration_adv.h b/config/examples/Anet/E10/Configuration_adv.h index 211dec4591..912a44b4df 100644 --- a/config/examples/Anet/E10/Configuration_adv.h +++ b/config/examples/Anet/E10/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Anet/E16/Configuration.h b/config/examples/Anet/E16/Configuration.h index 4ed9862d46..2b586972e2 100644 --- a/config/examples/Anet/E16/Configuration.h +++ b/config/examples/Anet/E16/Configuration.h @@ -2076,7 +2076,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2346,13 +2346,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2369,7 +2369,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2377,12 +2377,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Anet/E16/Configuration_adv.h b/config/examples/Anet/E16/Configuration_adv.h index bf393fc164..a944823b27 100644 --- a/config/examples/Anet/E16/Configuration_adv.h +++ b/config/examples/Anet/E16/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/AnyCubic/Mega Zero/Configuration.h b/config/examples/AnyCubic/Mega Zero/Configuration.h index d8e4ed5f10..28a762fc6c 100644 --- a/config/examples/AnyCubic/Mega Zero/Configuration.h +++ b/config/examples/AnyCubic/Mega Zero/Configuration.h @@ -2070,7 +2070,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2340,13 +2340,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2363,7 +2363,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2371,12 +2371,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/AnyCubic/Mega Zero/Configuration_adv.h b/config/examples/AnyCubic/Mega Zero/Configuration_adv.h index adcfcfcc74..344fd0c69a 100644 --- a/config/examples/AnyCubic/Mega Zero/Configuration_adv.h +++ b/config/examples/AnyCubic/Mega Zero/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/AnyCubic/i3 Mega/Configuration.h b/config/examples/AnyCubic/i3 Mega/Configuration.h index 0ce921a153..01c902bb94 100644 --- a/config/examples/AnyCubic/i3 Mega/Configuration.h +++ b/config/examples/AnyCubic/i3 Mega/Configuration.h @@ -2093,7 +2093,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2377,13 +2377,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2400,7 +2400,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2408,12 +2408,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/AnyCubic/i3 Mega/Configuration_adv.h b/config/examples/AnyCubic/i3 Mega/Configuration_adv.h index 0ecba7af7c..986febc0cf 100644 --- a/config/examples/AnyCubic/i3 Mega/Configuration_adv.h +++ b/config/examples/AnyCubic/i3 Mega/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/AnyCubic/i3/Configuration.h b/config/examples/AnyCubic/i3/Configuration.h index 3de0609e0e..1679dcb099 100644 --- a/config/examples/AnyCubic/i3/Configuration.h +++ b/config/examples/AnyCubic/i3/Configuration.h @@ -2074,7 +2074,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2344,13 +2344,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2367,7 +2367,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2375,12 +2375,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/AnyCubic/i3/Configuration_adv.h b/config/examples/AnyCubic/i3/Configuration_adv.h index 35a712bdf8..9fe0de4dba 100644 --- a/config/examples/AnyCubic/i3/Configuration_adv.h +++ b/config/examples/AnyCubic/i3/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/ArmEd/Configuration.h b/config/examples/ArmEd/Configuration.h index 2161bb3a67..80872791f9 100644 --- a/config/examples/ArmEd/Configuration.h +++ b/config/examples/ArmEd/Configuration.h @@ -2065,7 +2065,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2335,13 +2335,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2358,7 +2358,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2366,12 +2366,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/ArmEd/Configuration_adv.h b/config/examples/ArmEd/Configuration_adv.h index ee90f0cf38..15c35e3912 100644 --- a/config/examples/ArmEd/Configuration_adv.h +++ b/config/examples/ArmEd/Configuration_adv.h @@ -494,7 +494,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Artillery/Genius/Configuration.h b/config/examples/Artillery/Genius/Configuration.h index 64cf0b64eb..6a12577ddb 100644 --- a/config/examples/Artillery/Genius/Configuration.h +++ b/config/examples/Artillery/Genius/Configuration.h @@ -2047,7 +2047,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2317,13 +2317,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2340,7 +2340,7 @@ #define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2348,12 +2348,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Artillery/Genius/Configuration_adv.h b/config/examples/Artillery/Genius/Configuration_adv.h index f8e8184aae..4b81c12e82 100644 --- a/config/examples/Artillery/Genius/Configuration_adv.h +++ b/config/examples/Artillery/Genius/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Artillery/Sidewinder X1/Configuration.h b/config/examples/Artillery/Sidewinder X1/Configuration.h index 2a47aaa128..9a93bdca47 100644 --- a/config/examples/Artillery/Sidewinder X1/Configuration.h +++ b/config/examples/Artillery/Sidewinder X1/Configuration.h @@ -2069,7 +2069,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2339,13 +2339,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2362,7 +2362,7 @@ #define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2370,12 +2370,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Artillery/Sidewinder X1/Configuration_adv.h b/config/examples/Artillery/Sidewinder X1/Configuration_adv.h index f9746df530..9ed8a7d490 100644 --- a/config/examples/Artillery/Sidewinder X1/Configuration_adv.h +++ b/config/examples/Artillery/Sidewinder X1/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Artillery/Sidewinder X1_0.9_degree_BMG_E3D_V6/Configuration.h b/config/examples/Artillery/Sidewinder X1_0.9_degree_BMG_E3D_V6/Configuration.h index 0e1c16b146..bbb4bbde1c 100644 --- a/config/examples/Artillery/Sidewinder X1_0.9_degree_BMG_E3D_V6/Configuration.h +++ b/config/examples/Artillery/Sidewinder X1_0.9_degree_BMG_E3D_V6/Configuration.h @@ -2079,7 +2079,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2349,13 +2349,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2372,7 +2372,7 @@ #define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2380,12 +2380,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Artillery/Sidewinder X1_0.9_degree_BMG_E3D_V6/Configuration_adv.h b/config/examples/Artillery/Sidewinder X1_0.9_degree_BMG_E3D_V6/Configuration_adv.h index be2180206e..e367da2c98 100644 --- a/config/examples/Artillery/Sidewinder X1_0.9_degree_BMG_E3D_V6/Configuration_adv.h +++ b/config/examples/Artillery/Sidewinder X1_0.9_degree_BMG_E3D_V6/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Azteeg/X5GT/Configuration.h b/config/examples/Azteeg/X5GT/Configuration.h index 9eae98ea43..96af77001e 100644 --- a/config/examples/Azteeg/X5GT/Configuration.h +++ b/config/examples/Azteeg/X5GT/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration.h b/config/examples/BIBO/TouchX/cyclops/Configuration.h index c5fd7fd188..f4b2b98ad4 100644 --- a/config/examples/BIBO/TouchX/cyclops/Configuration.h +++ b/config/examples/BIBO/TouchX/cyclops/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h index 127e5e2ad4..2109cbc3ce 100644 --- a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h +++ b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/BIBO/TouchX/default/Configuration.h b/config/examples/BIBO/TouchX/default/Configuration.h index eff034d235..8efd822d6f 100644 --- a/config/examples/BIBO/TouchX/default/Configuration.h +++ b/config/examples/BIBO/TouchX/default/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/BIBO/TouchX/default/Configuration_adv.h b/config/examples/BIBO/TouchX/default/Configuration_adv.h index da67eecbae..5d8865efae 100644 --- a/config/examples/BIBO/TouchX/default/Configuration_adv.h +++ b/config/examples/BIBO/TouchX/default/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/BIQU/B1-BLTouch/Configuration.h b/config/examples/BIQU/B1-BLTouch/Configuration.h index 84da8ad101..fb5b25bac6 100644 --- a/config/examples/BIQU/B1-BLTouch/Configuration.h +++ b/config/examples/BIQU/B1-BLTouch/Configuration.h @@ -2078,7 +2078,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2344,13 +2344,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2367,7 +2367,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver #define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2375,12 +2375,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 2 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 2 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used //#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) #define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/BIQU/B1-BLTouch/Configuration_adv.h b/config/examples/BIQU/B1-BLTouch/Configuration_adv.h index 7f89ac9a98..5291e29068 100644 --- a/config/examples/BIQU/B1-BLTouch/Configuration_adv.h +++ b/config/examples/BIQU/B1-BLTouch/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/BIQU/B1/Configuration.h b/config/examples/BIQU/B1/Configuration.h index dd3e15a0e3..4014852639 100644 --- a/config/examples/BIQU/B1/Configuration.h +++ b/config/examples/BIQU/B1/Configuration.h @@ -2078,7 +2078,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2344,13 +2344,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2367,7 +2367,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver #define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2375,12 +2375,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 2 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 2 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used //#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) #define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/BIQU/B1/Configuration_adv.h b/config/examples/BIQU/B1/Configuration_adv.h index 490d1c069b..cdfdc62976 100644 --- a/config/examples/BIQU/B1/Configuration_adv.h +++ b/config/examples/BIQU/B1/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/BQ/Hephestos/Configuration.h b/config/examples/BQ/Hephestos/Configuration.h index ee99de31e6..ad10a52c10 100644 --- a/config/examples/BQ/Hephestos/Configuration.h +++ b/config/examples/BQ/Hephestos/Configuration.h @@ -2052,7 +2052,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2322,13 +2322,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2345,7 +2345,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2353,12 +2353,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/BQ/Hephestos/Configuration_adv.h b/config/examples/BQ/Hephestos/Configuration_adv.h index 6234bb30f8..811cdd2a88 100644 --- a/config/examples/BQ/Hephestos/Configuration_adv.h +++ b/config/examples/BQ/Hephestos/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/BQ/Hephestos_2/Configuration.h b/config/examples/BQ/Hephestos_2/Configuration.h index 28aab8a0c9..447140eb88 100644 --- a/config/examples/BQ/Hephestos_2/Configuration.h +++ b/config/examples/BQ/Hephestos_2/Configuration.h @@ -2065,7 +2065,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2335,13 +2335,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2358,7 +2358,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2366,12 +2366,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/BQ/Hephestos_2/Configuration_adv.h b/config/examples/BQ/Hephestos_2/Configuration_adv.h index b045e3c1dd..b47e80f9b9 100644 --- a/config/examples/BQ/Hephestos_2/Configuration_adv.h +++ b/config/examples/BQ/Hephestos_2/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/BQ/WITBOX/Configuration.h b/config/examples/BQ/WITBOX/Configuration.h index 1dddffa9d0..a88111955b 100644 --- a/config/examples/BQ/WITBOX/Configuration.h +++ b/config/examples/BQ/WITBOX/Configuration.h @@ -2052,7 +2052,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2322,13 +2322,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2345,7 +2345,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2353,12 +2353,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/BQ/WITBOX/Configuration_adv.h b/config/examples/BQ/WITBOX/Configuration_adv.h index edf325b1a6..7bad761382 100644 --- a/config/examples/BQ/WITBOX/Configuration_adv.h +++ b/config/examples/BQ/WITBOX/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h b/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h index fe91d671e5..91cafe0af2 100644 --- a/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h +++ b/config/examples/CTC/i3 2560 Rev A/no probe/Configuration.h @@ -2069,7 +2069,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2339,13 +2339,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2362,7 +2362,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2370,12 +2370,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Cartesio/Configuration.h b/config/examples/Cartesio/Configuration.h index b7f8c04bf8..5617de43a1 100644 --- a/config/examples/Cartesio/Configuration.h +++ b/config/examples/Cartesio/Configuration.h @@ -2063,7 +2063,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2333,13 +2333,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2356,7 +2356,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2364,12 +2364,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Cartesio/Configuration_adv.h b/config/examples/Cartesio/Configuration_adv.h index 0a65d88dbd..4eda8991fd 100644 --- a/config/examples/Cartesio/Configuration_adv.h +++ b/config/examples/Cartesio/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Copymaster3D/300/Configuration.h b/config/examples/Copymaster3D/300/Configuration.h index 596206840c..dc496daf61 100644 --- a/config/examples/Copymaster3D/300/Configuration.h +++ b/config/examples/Copymaster3D/300/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Copymaster3D/400/Configuration.h b/config/examples/Copymaster3D/400/Configuration.h index 25dc0c166a..bad37e8896 100644 --- a/config/examples/Copymaster3D/400/Configuration.h +++ b/config/examples/Copymaster3D/400/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Copymaster3D/500/Configuration.h b/config/examples/Copymaster3D/500/Configuration.h index 996528b666..332e2f5dc0 100644 --- a/config/examples/Copymaster3D/500/Configuration.h +++ b/config/examples/Copymaster3D/500/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Creality/CR-10 V2/Configuration.h b/config/examples/Creality/CR-10 V2/Configuration.h index 36d924c2d4..8e4e66df52 100644 --- a/config/examples/Creality/CR-10 V2/Configuration.h +++ b/config/examples/Creality/CR-10 V2/Configuration.h @@ -2095,7 +2095,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2365,13 +2365,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2388,7 +2388,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2396,12 +2396,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Creality/CR-10 V2/Configuration_adv.h b/config/examples/Creality/CR-10 V2/Configuration_adv.h index 334b36e395..082b2cef37 100644 --- a/config/examples/Creality/CR-10 V2/Configuration_adv.h +++ b/config/examples/Creality/CR-10 V2/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Creality/CR-10/Configuration.h b/config/examples/Creality/CR-10/Configuration.h index 0e9e01c6be..f5f2c02584 100644 --- a/config/examples/Creality/CR-10/Configuration.h +++ b/config/examples/Creality/CR-10/Configuration.h @@ -2074,7 +2074,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2344,13 +2344,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2367,7 +2367,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2375,12 +2375,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Creality/CR-10/Configuration_adv.h b/config/examples/Creality/CR-10/Configuration_adv.h index e8a04b8176..4d3dd3cfcc 100644 --- a/config/examples/Creality/CR-10/Configuration_adv.h +++ b/config/examples/Creality/CR-10/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Creality/CR-10S/Configuration.h b/config/examples/Creality/CR-10S/Configuration.h index 21c1667ace..0276c83078 100644 --- a/config/examples/Creality/CR-10S/Configuration.h +++ b/config/examples/Creality/CR-10S/Configuration.h @@ -2065,7 +2065,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2335,13 +2335,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2358,7 +2358,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2366,12 +2366,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Creality/CR-10S/Configuration_adv.h b/config/examples/Creality/CR-10S/Configuration_adv.h index bad952f52d..af59592bee 100644 --- a/config/examples/Creality/CR-10S/Configuration_adv.h +++ b/config/examples/Creality/CR-10S/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Creality/CR-10_5S/Configuration.h b/config/examples/Creality/CR-10_5S/Configuration.h index 264cf61a2f..1be3e209d0 100644 --- a/config/examples/Creality/CR-10_5S/Configuration.h +++ b/config/examples/Creality/CR-10_5S/Configuration.h @@ -2067,7 +2067,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2337,13 +2337,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2360,7 +2360,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2368,12 +2368,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Creality/CR-10_5S/Configuration_adv.h b/config/examples/Creality/CR-10_5S/Configuration_adv.h index 8c195d00d0..f9a8b4eb4c 100644 --- a/config/examples/Creality/CR-10_5S/Configuration_adv.h +++ b/config/examples/Creality/CR-10_5S/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Creality/CR-10mini/CrealityV1/Configuration.h b/config/examples/Creality/CR-10mini/CrealityV1/Configuration.h index 55835e42af..cc6e39ef3e 100644 --- a/config/examples/Creality/CR-10mini/CrealityV1/Configuration.h +++ b/config/examples/Creality/CR-10mini/CrealityV1/Configuration.h @@ -2083,7 +2083,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2353,13 +2353,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2376,7 +2376,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2384,12 +2384,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Creality/CR-10mini/CrealityV1/Configuration_adv.h b/config/examples/Creality/CR-10mini/CrealityV1/Configuration_adv.h index 689c31eec2..a27b036d18 100644 --- a/config/examples/Creality/CR-10mini/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/CR-10mini/CrealityV1/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Creality/CR-10mini/MEEB-3DP/Configuration.h b/config/examples/Creality/CR-10mini/MEEB-3DP/Configuration.h index 082b75fc51..2ea550962b 100644 --- a/config/examples/Creality/CR-10mini/MEEB-3DP/Configuration.h +++ b/config/examples/Creality/CR-10mini/MEEB-3DP/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver #define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRB @@ -2370,7 +2370,7 @@ #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness (0-255) #define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Creality/CR-10mini/MEEB-3DP/Configuration_adv.h b/config/examples/Creality/CR-10mini/MEEB-3DP/Configuration_adv.h index ee4eb18e14..65d6a7b071 100644 --- a/config/examples/Creality/CR-10mini/MEEB-3DP/Configuration_adv.h +++ b/config/examples/Creality/CR-10mini/MEEB-3DP/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Creality/CR-20 Pro/Configuration.h b/config/examples/Creality/CR-20 Pro/Configuration.h index b6e4411f12..0d603ab2bb 100644 --- a/config/examples/Creality/CR-20 Pro/Configuration.h +++ b/config/examples/Creality/CR-20 Pro/Configuration.h @@ -2072,7 +2072,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2342,13 +2342,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2365,7 +2365,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2373,12 +2373,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Creality/CR-20 Pro/Configuration_adv.h b/config/examples/Creality/CR-20 Pro/Configuration_adv.h index 59a7ea32bf..40cdab6eed 100644 --- a/config/examples/Creality/CR-20 Pro/Configuration_adv.h +++ b/config/examples/Creality/CR-20 Pro/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Creality/CR-20/Configuration.h b/config/examples/Creality/CR-20/Configuration.h index 855d8aacad..ab62a1b9f3 100644 --- a/config/examples/Creality/CR-20/Configuration.h +++ b/config/examples/Creality/CR-20/Configuration.h @@ -2072,7 +2072,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2342,13 +2342,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2365,7 +2365,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2373,12 +2373,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Creality/CR-20/Configuration_adv.h b/config/examples/Creality/CR-20/Configuration_adv.h index 9a5d03a2ed..2ea0c68ca6 100644 --- a/config/examples/Creality/CR-20/Configuration_adv.h +++ b/config/examples/Creality/CR-20/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Creality/CR-8/Configuration.h b/config/examples/Creality/CR-8/Configuration.h index 1e03947c5b..a5136ac21e 100644 --- a/config/examples/Creality/CR-8/Configuration.h +++ b/config/examples/Creality/CR-8/Configuration.h @@ -2074,7 +2074,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2344,13 +2344,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2367,7 +2367,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2375,12 +2375,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Creality/CR-8/Configuration_adv.h b/config/examples/Creality/CR-8/Configuration_adv.h index 7ad33a9c25..80908e1502 100644 --- a/config/examples/Creality/CR-8/Configuration_adv.h +++ b/config/examples/Creality/CR-8/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Creality/Ender-2/Configuration.h b/config/examples/Creality/Ender-2/Configuration.h index b65129e6c2..a6c4463741 100644 --- a/config/examples/Creality/Ender-2/Configuration.h +++ b/config/examples/Creality/Ender-2/Configuration.h @@ -2068,7 +2068,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2338,13 +2338,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2361,7 +2361,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2369,12 +2369,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Creality/Ender-2/Configuration_adv.h b/config/examples/Creality/Ender-2/Configuration_adv.h index ebf07e0e61..581f82a183 100644 --- a/config/examples/Creality/Ender-2/Configuration_adv.h +++ b/config/examples/Creality/Ender-2/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Creality/Ender-3 Pro V1.5/Configuration.h b/config/examples/Creality/Ender-3 Pro V1.5/Configuration.h index 9f9956612e..63eeefc6a6 100644 --- a/config/examples/Creality/Ender-3 Pro V1.5/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro V1.5/Configuration.h @@ -2065,7 +2065,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2340,13 +2340,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2363,7 +2363,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2371,12 +2371,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Creality/Ender-3 Pro V1.5/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro V1.5/Configuration_adv.h index 4b741e0587..8b811f3696 100644 --- a/config/examples/Creality/Ender-3 Pro V1.5/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Pro V1.5/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Creality/Ender-3 Pro/Configuration.h b/config/examples/Creality/Ender-3 Pro/Configuration.h index fe23d358ba..a4b26b5723 100644 --- a/config/examples/Creality/Ender-3 Pro/Configuration.h +++ b/config/examples/Creality/Ender-3 Pro/Configuration.h @@ -2068,7 +2068,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2338,13 +2338,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2361,7 +2361,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2369,12 +2369,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Creality/Ender-3 Pro/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro/Configuration_adv.h index e06ed7a34b..971bf1fa2d 100644 --- a/config/examples/Creality/Ender-3 Pro/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Pro/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Creality/Ender-3 V2/Configuration.h b/config/examples/Creality/Ender-3 V2/Configuration.h index 471659c436..8f6d7e2ada 100644 --- a/config/examples/Creality/Ender-3 V2/Configuration.h +++ b/config/examples/Creality/Ender-3 V2/Configuration.h @@ -2065,7 +2065,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2335,13 +2335,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2358,7 +2358,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2366,12 +2366,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 4 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 4 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Creality/Ender-3 V2/Configuration_adv.h b/config/examples/Creality/Ender-3 V2/Configuration_adv.h index 09a625d1a6..33cc214f2d 100644 --- a/config/examples/Creality/Ender-3 V2/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 V2/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h index 1e94204681..e8e1d06cc5 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration.h @@ -2056,7 +2056,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2326,13 +2326,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2349,7 +2349,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2357,12 +2357,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h index 2e33f11971..0334e44c76 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h index 8858bb6b9f..15405f3a49 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration.h @@ -2057,7 +2057,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2327,13 +2327,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2350,7 +2350,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2358,12 +2358,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h index 15babecde1..d6dfb21286 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h index c9016515f2..5371845ef4 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -2057,7 +2057,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2327,13 +2327,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2350,7 +2350,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2358,12 +2358,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h index 0725c6f886..952dc7e2d1 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Creality/Ender-3/CrealityV1/Configuration.h b/config/examples/Creality/Ender-3/CrealityV1/Configuration.h index 028436a5be..cec934d3f4 100644 --- a/config/examples/Creality/Ender-3/CrealityV1/Configuration.h +++ b/config/examples/Creality/Ender-3/CrealityV1/Configuration.h @@ -2068,7 +2068,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2338,13 +2338,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2361,7 +2361,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2369,12 +2369,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Creality/Ender-3/CrealityV1/Configuration_adv.h b/config/examples/Creality/Ender-3/CrealityV1/Configuration_adv.h index 4e2f531d0d..482fdb16f8 100644 --- a/config/examples/Creality/Ender-3/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/CrealityV1/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h index 1094ec1136..a98c58c116 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration.h @@ -2069,7 +2069,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2339,13 +2339,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2362,7 +2362,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2370,12 +2370,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration_adv.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration_adv.h index 109272d685..7f0b9cc61a 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h index 450a01612d..8941c6a5b2 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration.h @@ -2069,7 +2069,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2339,13 +2339,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2362,7 +2362,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2370,12 +2370,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration_adv.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration_adv.h index 0f01730891..dc81bcd0bc 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h index e33ee82c30..865567591d 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration.h @@ -2069,7 +2069,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2339,13 +2339,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2362,7 +2362,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2370,12 +2370,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration_adv.h b/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration_adv.h index df7f3bed58..b044941a7b 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h b/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h index c6bf1bfb4f..96aefe21fa 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration.h @@ -2069,7 +2069,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2339,13 +2339,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2362,7 +2362,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2370,12 +2370,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration_adv.h b/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration_adv.h index c8f59d1041..1321fd18a8 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h b/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h index fce9a4c4d4..f62527735d 100644 --- a/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h +++ b/config/examples/Creality/Ender-3/MEEB-3DP/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver #define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2370,7 +2370,7 @@ #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness (0-255) #define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Creality/Ender-3/MEEB-3DP/Configuration_adv.h b/config/examples/Creality/Ender-3/MEEB-3DP/Configuration_adv.h index 5620643c2b..03749f3eda 100644 --- a/config/examples/Creality/Ender-3/MEEB-3DP/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/MEEB-3DP/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Creality/Ender-4/Configuration.h b/config/examples/Creality/Ender-4/Configuration.h index ac5d564324..f111f900e8 100644 --- a/config/examples/Creality/Ender-4/Configuration.h +++ b/config/examples/Creality/Ender-4/Configuration.h @@ -2074,7 +2074,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2344,13 +2344,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2367,7 +2367,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2375,12 +2375,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Creality/Ender-4/Configuration_adv.h b/config/examples/Creality/Ender-4/Configuration_adv.h index a43c9b64f5..25f8531abe 100644 --- a/config/examples/Creality/Ender-4/Configuration_adv.h +++ b/config/examples/Creality/Ender-4/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm #define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Creality/Ender-5 Pro/Configuration.h b/config/examples/Creality/Ender-5 Pro/Configuration.h index 43a396a96b..40e11d3e91 100644 --- a/config/examples/Creality/Ender-5 Pro/Configuration.h +++ b/config/examples/Creality/Ender-5 Pro/Configuration.h @@ -2062,7 +2062,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2332,13 +2332,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2355,7 +2355,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2363,12 +2363,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Creality/Ender-5 Pro/Configuration_adv.h b/config/examples/Creality/Ender-5 Pro/Configuration_adv.h index e67c9a8a7a..854cab58fb 100644 --- a/config/examples/Creality/Ender-5 Pro/Configuration_adv.h +++ b/config/examples/Creality/Ender-5 Pro/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h index 8d732883db..0f47a6e50a 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h @@ -2105,7 +2105,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2375,13 +2375,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2398,7 +2398,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2406,12 +2406,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration_adv.h b/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration_adv.h index d40cc239fb..b06729da57 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration_adv.h @@ -494,7 +494,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h index 02046f5b8f..36eef6c5fb 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration.h @@ -2057,7 +2057,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2327,13 +2327,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2350,7 +2350,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2358,12 +2358,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 10 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 10 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h index 1ec49e1a4e..b40f119358 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Creality/Ender-5/Creality/Configuration.h b/config/examples/Creality/Ender-5/Creality/Configuration.h index a241faec83..310789739e 100644 --- a/config/examples/Creality/Ender-5/Creality/Configuration.h +++ b/config/examples/Creality/Ender-5/Creality/Configuration.h @@ -2068,7 +2068,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2338,13 +2338,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2361,7 +2361,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2369,12 +2369,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Creality/Ender-5/Creality/Configuration_adv.h b/config/examples/Creality/Ender-5/Creality/Configuration_adv.h index 1a7f1e4205..ea3a4462c6 100644 --- a/config/examples/Creality/Ender-5/Creality/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/Creality/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Creality/Ender-5_Plus/Configuration.h b/config/examples/Creality/Ender-5_Plus/Configuration.h index a10ed06101..0a01bd9912 100644 --- a/config/examples/Creality/Ender-5_Plus/Configuration.h +++ b/config/examples/Creality/Ender-5_Plus/Configuration.h @@ -2056,7 +2056,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2327,13 +2327,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2350,7 +2350,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2358,12 +2358,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Creality/Ender-5_Plus/Configuration_adv.h b/config/examples/Creality/Ender-5_Plus/Configuration_adv.h index c9ef9a8419..113065cf5f 100644 --- a/config/examples/Creality/Ender-5_Plus/Configuration_adv.h +++ b/config/examples/Creality/Ender-5_Plus/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Dagoma/Disco Ultimate/Configuration.h b/config/examples/Dagoma/Disco Ultimate/Configuration.h index 3fbb892c14..89be6239e1 100644 --- a/config/examples/Dagoma/Disco Ultimate/Configuration.h +++ b/config/examples/Dagoma/Disco Ultimate/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h index 499c8fb77d..9d6230a1c1 100644 --- a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h +++ b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Daycom/3DP-100/Configuration.h b/config/examples/Daycom/3DP-100/Configuration.h index 7f4b038832..ada2ce075c 100644 --- a/config/examples/Daycom/3DP-100/Configuration.h +++ b/config/examples/Daycom/3DP-100/Configuration.h @@ -2071,7 +2071,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2341,13 +2341,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2364,7 +2364,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2372,12 +2372,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Daycom/3DP-100/Configuration_adv.h b/config/examples/Daycom/3DP-100/Configuration_adv.h index 3c3631adb0..ce410c7580 100644 --- a/config/examples/Daycom/3DP-100/Configuration_adv.h +++ b/config/examples/Daycom/3DP-100/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/EXP3D/Imprimante multifonction/Configuration.h b/config/examples/EXP3D/Imprimante multifonction/Configuration.h index a799ca0b62..30a05214a0 100644 --- a/config/examples/EXP3D/Imprimante multifonction/Configuration.h +++ b/config/examples/EXP3D/Imprimante multifonction/Configuration.h @@ -2062,7 +2062,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2332,13 +2332,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2355,7 +2355,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2363,12 +2363,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h b/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h index a6efeca341..b2d8029d38 100644 --- a/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h +++ b/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Einstart-S/Configuration.h b/config/examples/Einstart-S/Configuration.h index d58e689696..d97b1318df 100644 --- a/config/examples/Einstart-S/Configuration.h +++ b/config/examples/Einstart-S/Configuration.h @@ -2074,7 +2074,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2344,13 +2344,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2367,7 +2367,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2375,12 +2375,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Einstart-S/Configuration_adv.h b/config/examples/Einstart-S/Configuration_adv.h index 011341798c..e8d832526d 100644 --- a/config/examples/Einstart-S/Configuration_adv.h +++ b/config/examples/Einstart-S/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/FYSETC/AIO_II/Configuration.h b/config/examples/FYSETC/AIO_II/Configuration.h index 621eebb4f7..ce1206397e 100644 --- a/config/examples/FYSETC/AIO_II/Configuration.h +++ b/config/examples/FYSETC/AIO_II/Configuration.h @@ -2069,7 +2069,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) #define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2339,13 +2339,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2362,7 +2362,7 @@ #define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2370,12 +2370,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/FYSETC/AIO_II/Configuration_adv.h b/config/examples/FYSETC/AIO_II/Configuration_adv.h index 4bedce8064..c8c33963b0 100644 --- a/config/examples/FYSETC/AIO_II/Configuration_adv.h +++ b/config/examples/FYSETC/AIO_II/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/FYSETC/F6_13/Configuration.h b/config/examples/FYSETC/F6_13/Configuration.h index 417cb7a90c..0c8335abac 100644 --- a/config/examples/FYSETC/F6_13/Configuration.h +++ b/config/examples/FYSETC/F6_13/Configuration.h @@ -2066,7 +2066,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2336,13 +2336,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2363,7 +2363,7 @@ #define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2371,12 +2371,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/FYSETC/F6_13/Configuration_adv.h b/config/examples/FYSETC/F6_13/Configuration_adv.h index b50a6937e3..4c16913b52 100644 --- a/config/examples/FYSETC/F6_13/Configuration_adv.h +++ b/config/examples/FYSETC/F6_13/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/FYSETC/S6/Configuration.h b/config/examples/FYSETC/S6/Configuration.h index f06073f991..a5b7b1ca37 100644 --- a/config/examples/FYSETC/S6/Configuration.h +++ b/config/examples/FYSETC/S6/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/FYSETC/S6/Configuration_adv.h b/config/examples/FYSETC/S6/Configuration_adv.h index 7c65cbc88a..e6d1df2c35 100644 --- a/config/examples/FYSETC/S6/Configuration_adv.h +++ b/config/examples/FYSETC/S6/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Felix/DUAL/Configuration.h b/config/examples/Felix/DUAL/Configuration.h index 6a9f4d8b5c..f7a10a4b75 100644 --- a/config/examples/Felix/DUAL/Configuration.h +++ b/config/examples/Felix/DUAL/Configuration.h @@ -2046,7 +2046,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2316,13 +2316,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2339,7 +2339,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2347,12 +2347,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Felix/DUAL/Configuration_adv.h b/config/examples/Felix/DUAL/Configuration_adv.h index b117b29fe4..0c639552e8 100644 --- a/config/examples/Felix/DUAL/Configuration_adv.h +++ b/config/examples/Felix/DUAL/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Felix/Single/Configuration.h b/config/examples/Felix/Single/Configuration.h index 41598c1e07..b107e394e1 100644 --- a/config/examples/Felix/Single/Configuration.h +++ b/config/examples/Felix/Single/Configuration.h @@ -2046,7 +2046,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2316,13 +2316,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2339,7 +2339,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2347,12 +2347,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Felix/Single/Configuration_adv.h b/config/examples/Felix/Single/Configuration_adv.h index 3d283edbbd..9ba5eb0a41 100644 --- a/config/examples/Felix/Single/Configuration_adv.h +++ b/config/examples/Felix/Single/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/FlashForge/Creator 2X/Configuration.h b/config/examples/FlashForge/Creator 2X/Configuration.h index 3b072f0035..747d626a5e 100644 --- a/config/examples/FlashForge/Creator 2X/Configuration.h +++ b/config/examples/FlashForge/Creator 2X/Configuration.h @@ -2056,7 +2056,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2326,13 +2326,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2349,7 +2349,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2357,12 +2357,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/FlashForge/Creator 2X/Configuration_adv.h b/config/examples/FlashForge/Creator 2X/Configuration_adv.h index a06da609ad..fbc32f567b 100644 --- a/config/examples/FlashForge/Creator 2X/Configuration_adv.h +++ b/config/examples/FlashForge/Creator 2X/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/FlashForge/CreatorPro/Configuration.h b/config/examples/FlashForge/CreatorPro/Configuration.h index 9fa8f47d56..1c72730fd3 100644 --- a/config/examples/FlashForge/CreatorPro/Configuration.h +++ b/config/examples/FlashForge/CreatorPro/Configuration.h @@ -2057,7 +2057,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2327,13 +2327,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2350,7 +2350,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2358,12 +2358,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/FlashForge/CreatorPro/Configuration_adv.h b/config/examples/FlashForge/CreatorPro/Configuration_adv.h index 68c1765cef..d75f0dd8ec 100644 --- a/config/examples/FlashForge/CreatorPro/Configuration_adv.h +++ b/config/examples/FlashForge/CreatorPro/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/FlyingBear/P905H/Configuration.h b/config/examples/FlyingBear/P905H/Configuration.h index 2d67e5e728..de1c261136 100644 --- a/config/examples/FlyingBear/P905H/Configuration.h +++ b/config/examples/FlyingBear/P905H/Configuration.h @@ -2068,7 +2068,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2339,13 +2339,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2362,7 +2362,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2370,12 +2370,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/FlyingBear/P905H/Configuration_adv.h b/config/examples/FlyingBear/P905H/Configuration_adv.h index f135636e88..6f46ca9796 100644 --- a/config/examples/FlyingBear/P905H/Configuration_adv.h +++ b/config/examples/FlyingBear/P905H/Configuration_adv.h @@ -491,7 +491,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/FolgerTech/i3-2020/Configuration.h b/config/examples/FolgerTech/i3-2020/Configuration.h index 0debe3d545..d42706211b 100644 --- a/config/examples/FolgerTech/i3-2020/Configuration.h +++ b/config/examples/FolgerTech/i3-2020/Configuration.h @@ -2070,7 +2070,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2340,13 +2340,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2363,7 +2363,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2371,12 +2371,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/FolgerTech/i3-2020/Configuration_adv.h b/config/examples/FolgerTech/i3-2020/Configuration_adv.h index aca2748279..4bfc0b69e1 100644 --- a/config/examples/FolgerTech/i3-2020/Configuration_adv.h +++ b/config/examples/FolgerTech/i3-2020/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Formbot/Raptor/Configuration.h b/config/examples/Formbot/Raptor/Configuration.h index 97e4d89b1a..a29ca27d24 100644 --- a/config/examples/Formbot/Raptor/Configuration.h +++ b/config/examples/Formbot/Raptor/Configuration.h @@ -2169,7 +2169,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2439,13 +2439,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2462,7 +2462,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2470,12 +2470,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Formbot/Raptor/Configuration_adv.h b/config/examples/Formbot/Raptor/Configuration_adv.h index 3d6243609e..7beb038176 100644 --- a/config/examples/Formbot/Raptor/Configuration_adv.h +++ b/config/examples/Formbot/Raptor/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm #define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Formbot/T_Rex_2+/Configuration.h b/config/examples/Formbot/T_Rex_2+/Configuration.h index d96a08dc66..f719ab0f24 100644 --- a/config/examples/Formbot/T_Rex_2+/Configuration.h +++ b/config/examples/Formbot/T_Rex_2+/Configuration.h @@ -2050,7 +2050,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2320,13 +2320,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2343,7 +2343,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2351,12 +2351,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h index 1a978e4bee..f3a07e8515 100644 --- a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h +++ b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm #define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Formbot/T_Rex_3/Configuration.h b/config/examples/Formbot/T_Rex_3/Configuration.h index 4c0621800f..5da9cb1f4a 100644 --- a/config/examples/Formbot/T_Rex_3/Configuration.h +++ b/config/examples/Formbot/T_Rex_3/Configuration.h @@ -2080,7 +2080,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2350,13 +2350,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2373,7 +2373,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2381,12 +2381,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Formbot/T_Rex_3/Configuration_adv.h b/config/examples/Formbot/T_Rex_3/Configuration_adv.h index 6397a9342d..8e0ae9822e 100644 --- a/config/examples/Formbot/T_Rex_3/Configuration_adv.h +++ b/config/examples/Formbot/T_Rex_3/Configuration_adv.h @@ -494,7 +494,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm #define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Geeetech/A10/Configuration.h b/config/examples/Geeetech/A10/Configuration.h index c68829a27d..2b383c408b 100644 --- a/config/examples/Geeetech/A10/Configuration.h +++ b/config/examples/Geeetech/A10/Configuration.h @@ -2047,7 +2047,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2317,13 +2317,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2340,7 +2340,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2348,12 +2348,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Geeetech/A10/Configuration_adv.h b/config/examples/Geeetech/A10/Configuration_adv.h index 118acd6a8b..f94eac9208 100644 --- a/config/examples/Geeetech/A10/Configuration_adv.h +++ b/config/examples/Geeetech/A10/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Geeetech/A10D/Configuration.h b/config/examples/Geeetech/A10D/Configuration.h index f3636a0be7..ebdf4ed289 100644 --- a/config/examples/Geeetech/A10D/Configuration.h +++ b/config/examples/Geeetech/A10D/Configuration.h @@ -2047,7 +2047,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2317,13 +2317,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2340,7 +2340,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2348,12 +2348,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Geeetech/A10D/Configuration_adv.h b/config/examples/Geeetech/A10D/Configuration_adv.h index 003c1e4b2c..91efba663a 100644 --- a/config/examples/Geeetech/A10D/Configuration_adv.h +++ b/config/examples/Geeetech/A10D/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Geeetech/A10M/Configuration.h b/config/examples/Geeetech/A10M/Configuration.h index d83cd88849..3b39fac41c 100644 --- a/config/examples/Geeetech/A10M/Configuration.h +++ b/config/examples/Geeetech/A10M/Configuration.h @@ -2049,7 +2049,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2319,13 +2319,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2342,7 +2342,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2350,12 +2350,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Geeetech/A10M/Configuration_adv.h b/config/examples/Geeetech/A10M/Configuration_adv.h index d67bbbec33..d92939fa47 100644 --- a/config/examples/Geeetech/A10M/Configuration_adv.h +++ b/config/examples/Geeetech/A10M/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Geeetech/A10T/Configuration.h b/config/examples/Geeetech/A10T/Configuration.h index 7e6aaf6cf0..2a7473ec46 100644 --- a/config/examples/Geeetech/A10T/Configuration.h +++ b/config/examples/Geeetech/A10T/Configuration.h @@ -2050,7 +2050,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2320,13 +2320,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2343,7 +2343,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2351,12 +2351,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Geeetech/A10T/Configuration_adv.h b/config/examples/Geeetech/A10T/Configuration_adv.h index f9c1005737..2d59cc831e 100644 --- a/config/examples/Geeetech/A10T/Configuration_adv.h +++ b/config/examples/Geeetech/A10T/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Geeetech/A20/Configuration.h b/config/examples/Geeetech/A20/Configuration.h index 7e7a7c22a9..3c61c2a046 100644 --- a/config/examples/Geeetech/A20/Configuration.h +++ b/config/examples/Geeetech/A20/Configuration.h @@ -2051,7 +2051,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2321,13 +2321,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2344,7 +2344,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2352,12 +2352,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Geeetech/A20/Configuration_adv.h b/config/examples/Geeetech/A20/Configuration_adv.h index 98e067d825..b813981361 100644 --- a/config/examples/Geeetech/A20/Configuration_adv.h +++ b/config/examples/Geeetech/A20/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Geeetech/A20M/Configuration.h b/config/examples/Geeetech/A20M/Configuration.h index 8a716de22d..b5a27a21cf 100644 --- a/config/examples/Geeetech/A20M/Configuration.h +++ b/config/examples/Geeetech/A20M/Configuration.h @@ -2052,7 +2052,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2322,13 +2322,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2345,7 +2345,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2353,12 +2353,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Geeetech/A20M/Configuration_adv.h b/config/examples/Geeetech/A20M/Configuration_adv.h index 9e4ee42144..1eb5feb9ee 100644 --- a/config/examples/Geeetech/A20M/Configuration_adv.h +++ b/config/examples/Geeetech/A20M/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Geeetech/A20T/Configuration.h b/config/examples/Geeetech/A20T/Configuration.h index 313d6a8e4f..f99237a8ad 100644 --- a/config/examples/Geeetech/A20T/Configuration.h +++ b/config/examples/Geeetech/A20T/Configuration.h @@ -2053,7 +2053,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2323,13 +2323,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2346,7 +2346,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2354,12 +2354,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Geeetech/A20T/Configuration_adv.h b/config/examples/Geeetech/A20T/Configuration_adv.h index 0f154f4202..b975aafbf2 100644 --- a/config/examples/Geeetech/A20T/Configuration_adv.h +++ b/config/examples/Geeetech/A20T/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Geeetech/A30/Configuration.h b/config/examples/Geeetech/A30/Configuration.h index 45998f7af6..5970f93bd9 100644 --- a/config/examples/Geeetech/A30/Configuration.h +++ b/config/examples/Geeetech/A30/Configuration.h @@ -2050,7 +2050,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2320,13 +2320,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2343,7 +2343,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2351,12 +2351,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Geeetech/A30/Configuration_adv.h b/config/examples/Geeetech/A30/Configuration_adv.h index 5491105bde..21ce7732e5 100644 --- a/config/examples/Geeetech/A30/Configuration_adv.h +++ b/config/examples/Geeetech/A30/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Geeetech/D200/Configuration.h b/config/examples/Geeetech/D200/Configuration.h index b3d23f5702..d0d43cbbb4 100644 --- a/config/examples/Geeetech/D200/Configuration.h +++ b/config/examples/Geeetech/D200/Configuration.h @@ -2050,7 +2050,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2320,13 +2320,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2343,7 +2343,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2351,12 +2351,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Geeetech/D200/Configuration_adv.h b/config/examples/Geeetech/D200/Configuration_adv.h index b1462f1a6a..e125441fe3 100644 --- a/config/examples/Geeetech/D200/Configuration_adv.h +++ b/config/examples/Geeetech/D200/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Geeetech/Duplicator5/Configuration.h b/config/examples/Geeetech/Duplicator5/Configuration.h index bab1dbd9f3..99bfb17467 100644 --- a/config/examples/Geeetech/Duplicator5/Configuration.h +++ b/config/examples/Geeetech/Duplicator5/Configuration.h @@ -2061,7 +2061,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2331,13 +2331,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2354,7 +2354,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2362,12 +2362,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Geeetech/Duplicator5/Configuration_adv.h b/config/examples/Geeetech/Duplicator5/Configuration_adv.h index d44a673442..6908c852d2 100644 --- a/config/examples/Geeetech/Duplicator5/Configuration_adv.h +++ b/config/examples/Geeetech/Duplicator5/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Geeetech/E180/Configuration.h b/config/examples/Geeetech/E180/Configuration.h index ec0121f83d..d114c727d4 100644 --- a/config/examples/Geeetech/E180/Configuration.h +++ b/config/examples/Geeetech/E180/Configuration.h @@ -2051,7 +2051,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2321,13 +2321,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2344,7 +2344,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2352,12 +2352,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Geeetech/E180/Configuration_adv.h b/config/examples/Geeetech/E180/Configuration_adv.h index bcff90bc79..de5baccb7e 100644 --- a/config/examples/Geeetech/E180/Configuration_adv.h +++ b/config/examples/Geeetech/E180/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Geeetech/GT2560/Configuration.h b/config/examples/Geeetech/GT2560/Configuration.h index a2e9607b71..834ce7c74f 100644 --- a/config/examples/Geeetech/GT2560/Configuration.h +++ b/config/examples/Geeetech/GT2560/Configuration.h @@ -2077,7 +2077,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2347,13 +2347,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2370,7 +2370,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2378,12 +2378,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h index 336ae50a4a..3e42837e9d 100644 --- a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h +++ b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Geeetech/M201/Configuration.h b/config/examples/Geeetech/M201/Configuration.h index 4f96b2c209..df2bd7db9b 100644 --- a/config/examples/Geeetech/M201/Configuration.h +++ b/config/examples/Geeetech/M201/Configuration.h @@ -2050,7 +2050,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2320,13 +2320,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2343,7 +2343,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2351,12 +2351,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Geeetech/M201/Configuration_adv.h b/config/examples/Geeetech/M201/Configuration_adv.h index 091606a3d9..e18e52bf2a 100644 --- a/config/examples/Geeetech/M201/Configuration_adv.h +++ b/config/examples/Geeetech/M201/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Geeetech/MeCreator2/Configuration.h b/config/examples/Geeetech/MeCreator2/Configuration.h index 16e1a4b71c..b2ff548ab7 100644 --- a/config/examples/Geeetech/MeCreator2/Configuration.h +++ b/config/examples/Geeetech/MeCreator2/Configuration.h @@ -2071,7 +2071,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2341,13 +2341,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2364,7 +2364,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2372,12 +2372,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Geeetech/MeCreator2/Configuration_adv.h b/config/examples/Geeetech/MeCreator2/Configuration_adv.h index 67087a082c..52042d95f9 100644 --- a/config/examples/Geeetech/MeCreator2/Configuration_adv.h +++ b/config/examples/Geeetech/MeCreator2/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm #define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Geeetech/Me_creator/Configuration.h b/config/examples/Geeetech/Me_creator/Configuration.h index 53349f21ec..856b21e2e5 100644 --- a/config/examples/Geeetech/Me_creator/Configuration.h +++ b/config/examples/Geeetech/Me_creator/Configuration.h @@ -2063,7 +2063,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2333,13 +2333,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2356,7 +2356,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2364,12 +2364,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Geeetech/Me_creator/Configuration_adv.h b/config/examples/Geeetech/Me_creator/Configuration_adv.h index 7feee5430c..e16fb1a439 100644 --- a/config/examples/Geeetech/Me_creator/Configuration_adv.h +++ b/config/examples/Geeetech/Me_creator/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Geeetech/Me_ducer/Configuration.h b/config/examples/Geeetech/Me_ducer/Configuration.h index 84291ef9e4..c8c3ba6178 100644 --- a/config/examples/Geeetech/Me_ducer/Configuration.h +++ b/config/examples/Geeetech/Me_ducer/Configuration.h @@ -2061,7 +2061,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2331,13 +2331,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2354,7 +2354,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2362,12 +2362,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Geeetech/Me_ducer/Configuration_adv.h b/config/examples/Geeetech/Me_ducer/Configuration_adv.h index 90972f19b0..b0a16c8223 100644 --- a/config/examples/Geeetech/Me_ducer/Configuration_adv.h +++ b/config/examples/Geeetech/Me_ducer/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Geeetech/PI3A PRO/Configuration.h b/config/examples/Geeetech/PI3A PRO/Configuration.h index 53b2aab982..42b2d4e3f1 100644 --- a/config/examples/Geeetech/PI3A PRO/Configuration.h +++ b/config/examples/Geeetech/PI3A PRO/Configuration.h @@ -2083,7 +2083,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2353,13 +2353,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2376,7 +2376,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2384,12 +2384,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Geeetech/PI3A PRO/Configuration_adv.h b/config/examples/Geeetech/PI3A PRO/Configuration_adv.h index d597d3ea35..678b294912 100644 --- a/config/examples/Geeetech/PI3A PRO/Configuration_adv.h +++ b/config/examples/Geeetech/PI3A PRO/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h index d8f1a1cce6..bc62ef5dbc 100644 --- a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h @@ -2083,7 +2083,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2353,13 +2353,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2376,7 +2376,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2384,12 +2384,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h index 7644157634..3ba6ff1cb9 100644 --- a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h @@ -2082,7 +2082,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2352,13 +2352,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2375,7 +2375,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2383,12 +2383,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h index eb649f9d51..a289e3060a 100644 --- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h index 093a4db746..4029b07692 100644 --- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h +++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h index 21e15b31b6..f35cf6a82b 100644 --- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h index 432b26f52d..39246402a4 100644 --- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h +++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/HMS434/Configuration.h b/config/examples/HMS434/Configuration.h index 76f4a3cd0c..eb3cd63f60 100644 --- a/config/examples/HMS434/Configuration.h +++ b/config/examples/HMS434/Configuration.h @@ -2049,7 +2049,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2319,13 +2319,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2342,7 +2342,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2350,12 +2350,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/HMS434/Configuration_adv.h b/config/examples/HMS434/Configuration_adv.h index 7c005060f9..df878f68e6 100644 --- a/config/examples/HMS434/Configuration_adv.h +++ b/config/examples/HMS434/Configuration_adv.h @@ -481,7 +481,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Infitary/i3-M508/Configuration.h b/config/examples/Infitary/i3-M508/Configuration.h index 3d140666fb..ec8334f1e4 100644 --- a/config/examples/Infitary/i3-M508/Configuration.h +++ b/config/examples/Infitary/i3-M508/Configuration.h @@ -2068,7 +2068,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2338,13 +2338,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2361,7 +2361,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2369,12 +2369,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Infitary/i3-M508/Configuration_adv.h b/config/examples/Infitary/i3-M508/Configuration_adv.h index 20a562c849..8d97a000ad 100644 --- a/config/examples/Infitary/i3-M508/Configuration_adv.h +++ b/config/examples/Infitary/i3-M508/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Intamsys/FunmatHT_4988/Configuration.h b/config/examples/Intamsys/FunmatHT_4988/Configuration.h index 8fc084b82a..6e6207fd7e 100644 --- a/config/examples/Intamsys/FunmatHT_4988/Configuration.h +++ b/config/examples/Intamsys/FunmatHT_4988/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Intamsys/FunmatHT_4988/Configuration_adv.h b/config/examples/Intamsys/FunmatHT_4988/Configuration_adv.h index 5068302fba..eb2cd0c3ce 100644 --- a/config/examples/Intamsys/FunmatHT_4988/Configuration_adv.h +++ b/config/examples/Intamsys/FunmatHT_4988/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm #define CASE_LIGHT_MENU // Add Case Light options to the LCD menu #define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/JGAurora/A1/Configuration.h b/config/examples/JGAurora/A1/Configuration.h index 3d3c1b786a..87ac8efd80 100644 --- a/config/examples/JGAurora/A1/Configuration.h +++ b/config/examples/JGAurora/A1/Configuration.h @@ -2068,7 +2068,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2340,13 +2340,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2363,7 +2363,7 @@ #define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2371,12 +2371,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/JGAurora/A1/Configuration_adv.h b/config/examples/JGAurora/A1/Configuration_adv.h index 3ad10fd19a..53ce3c350e 100644 --- a/config/examples/JGAurora/A1/Configuration_adv.h +++ b/config/examples/JGAurora/A1/Configuration_adv.h @@ -495,7 +495,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/JGAurora/A3/Configuration.h b/config/examples/JGAurora/A3/Configuration.h index c4f512d8c0..b4955235f0 100644 --- a/config/examples/JGAurora/A3/Configuration.h +++ b/config/examples/JGAurora/A3/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/JGAurora/A5/Configuration.h b/config/examples/JGAurora/A5/Configuration.h index 1eb8b3513c..17d3b55f1c 100644 --- a/config/examples/JGAurora/A5/Configuration.h +++ b/config/examples/JGAurora/A5/Configuration.h @@ -2075,7 +2075,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2345,13 +2345,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2368,7 +2368,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2376,12 +2376,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/JGAurora/A5/Configuration_adv.h b/config/examples/JGAurora/A5/Configuration_adv.h index f3122798a9..37336fc58c 100644 --- a/config/examples/JGAurora/A5/Configuration_adv.h +++ b/config/examples/JGAurora/A5/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/JGAurora/A5S/Configuration.h b/config/examples/JGAurora/A5S/Configuration.h index ce4313557d..e7c6725079 100644 --- a/config/examples/JGAurora/A5S/Configuration.h +++ b/config/examples/JGAurora/A5S/Configuration.h @@ -2068,7 +2068,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2340,13 +2340,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2363,7 +2363,7 @@ #define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2371,12 +2371,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/JGAurora/A5S/Configuration_adv.h b/config/examples/JGAurora/A5S/Configuration_adv.h index f572481f1d..6936d80089 100644 --- a/config/examples/JGAurora/A5S/Configuration_adv.h +++ b/config/examples/JGAurora/A5S/Configuration_adv.h @@ -495,7 +495,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/JGAurora/Magic/Configuration.h b/config/examples/JGAurora/Magic/Configuration.h index 4b36086d30..7d5bf4d2b7 100644 --- a/config/examples/JGAurora/Magic/Configuration.h +++ b/config/examples/JGAurora/Magic/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/JGAurora/Magic/Configuration_adv.h b/config/examples/JGAurora/Magic/Configuration_adv.h index 28af4704bf..9354f51e7b 100644 --- a/config/examples/JGAurora/Magic/Configuration_adv.h +++ b/config/examples/JGAurora/Magic/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Kingroon/KP3/Configuration.h b/config/examples/Kingroon/KP3/Configuration.h index 57f3683a30..c8969fcd52 100644 --- a/config/examples/Kingroon/KP3/Configuration.h +++ b/config/examples/Kingroon/KP3/Configuration.h @@ -2070,7 +2070,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2347,13 +2347,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2370,7 +2370,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2378,12 +2378,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Kingroon/KP3/Configuration_adv.h b/config/examples/Kingroon/KP3/Configuration_adv.h index f3b9da42da..3743a9a72b 100644 --- a/config/examples/Kingroon/KP3/Configuration_adv.h +++ b/config/examples/Kingroon/KP3/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/MBot/Cube/Configuration.h b/config/examples/MBot/Cube/Configuration.h index 5a471a6655..f7c3a2397f 100644 --- a/config/examples/MBot/Cube/Configuration.h +++ b/config/examples/MBot/Cube/Configuration.h @@ -2055,7 +2055,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2325,13 +2325,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2348,7 +2348,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2356,12 +2356,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/MBot/Cube/Configuration_adv.h b/config/examples/MBot/Cube/Configuration_adv.h index 32379cd9bc..d8cd985168 100644 --- a/config/examples/MBot/Cube/Configuration_adv.h +++ b/config/examples/MBot/Cube/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/MakerFarm/Pegasus_12/Configuration.h b/config/examples/MakerFarm/Pegasus_12/Configuration.h index fc8aa37347..9db0de9d9f 100644 --- a/config/examples/MakerFarm/Pegasus_12/Configuration.h +++ b/config/examples/MakerFarm/Pegasus_12/Configuration.h @@ -2067,7 +2067,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2337,13 +2337,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2360,7 +2360,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2368,12 +2368,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/MakerFarm/Pegasus_12/Configuration_adv.h b/config/examples/MakerFarm/Pegasus_12/Configuration_adv.h index 8334e8c1e2..d8dfd3c5aa 100644 --- a/config/examples/MakerFarm/Pegasus_12/Configuration_adv.h +++ b/config/examples/MakerFarm/Pegasus_12/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/MakerParts/Configuration.h b/config/examples/MakerParts/Configuration.h index 6ab3636624..7957522845 100644 --- a/config/examples/MakerParts/Configuration.h +++ b/config/examples/MakerParts/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/MakerParts/Configuration_adv.h b/config/examples/MakerParts/Configuration_adv.h index df68af6f84..90cc6c0311 100644 --- a/config/examples/MakerParts/Configuration_adv.h +++ b/config/examples/MakerParts/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Malyan/M150/Configuration.h b/config/examples/Malyan/M150/Configuration.h index 04518af6a9..3572baf94f 100644 --- a/config/examples/Malyan/M150/Configuration.h +++ b/config/examples/Malyan/M150/Configuration.h @@ -2092,7 +2092,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2362,13 +2362,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2385,7 +2385,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2393,12 +2393,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Malyan/M150/Configuration_adv.h b/config/examples/Malyan/M150/Configuration_adv.h index 97e7d503ac..b753dded77 100644 --- a/config/examples/Malyan/M150/Configuration_adv.h +++ b/config/examples/Malyan/M150/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Malyan/M200/Configuration.h b/config/examples/Malyan/M200/Configuration.h index 555fd4ca78..6ff20464fb 100644 --- a/config/examples/Malyan/M200/Configuration.h +++ b/config/examples/Malyan/M200/Configuration.h @@ -2074,7 +2074,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2344,13 +2344,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2367,7 +2367,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2375,12 +2375,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Malyan/M200/Configuration_adv.h b/config/examples/Malyan/M200/Configuration_adv.h index 395c478202..2dd3c54cf5 100644 --- a/config/examples/Malyan/M200/Configuration_adv.h +++ b/config/examples/Malyan/M200/Configuration_adv.h @@ -492,7 +492,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Micromake/C1/basic/Configuration.h b/config/examples/Micromake/C1/basic/Configuration.h index 88d39e3355..cb456c7119 100644 --- a/config/examples/Micromake/C1/basic/Configuration.h +++ b/config/examples/Micromake/C1/basic/Configuration.h @@ -2068,7 +2068,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2338,13 +2338,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2361,7 +2361,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2369,12 +2369,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Micromake/C1/enhanced/Configuration.h b/config/examples/Micromake/C1/enhanced/Configuration.h index 29ad7e1918..137ea9165e 100644 --- a/config/examples/Micromake/C1/enhanced/Configuration.h +++ b/config/examples/Micromake/C1/enhanced/Configuration.h @@ -2068,7 +2068,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2338,13 +2338,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2361,7 +2361,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2369,12 +2369,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Micromake/C1/enhanced/Configuration_adv.h b/config/examples/Micromake/C1/enhanced/Configuration_adv.h index 04e6152751..5c542dc9dc 100644 --- a/config/examples/Micromake/C1/enhanced/Configuration_adv.h +++ b/config/examples/Micromake/C1/enhanced/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Mks/Robin/Configuration.h b/config/examples/Mks/Robin/Configuration.h index e65e329546..25689a9277 100644 --- a/config/examples/Mks/Robin/Configuration.h +++ b/config/examples/Mks/Robin/Configuration.h @@ -2065,7 +2065,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2359,13 +2359,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2382,7 +2382,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2390,12 +2390,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Mks/Robin/Configuration_adv.h b/config/examples/Mks/Robin/Configuration_adv.h index 346b9ae6de..522f7daa62 100644 --- a/config/examples/Mks/Robin/Configuration_adv.h +++ b/config/examples/Mks/Robin/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Mks/Robin_Lite3/Configuration.h b/config/examples/Mks/Robin_Lite3/Configuration.h index 8012265885..633f6b75e5 100644 --- a/config/examples/Mks/Robin_Lite3/Configuration.h +++ b/config/examples/Mks/Robin_Lite3/Configuration.h @@ -2071,7 +2071,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2341,13 +2341,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2364,7 +2364,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2372,12 +2372,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Mks/Robin_Pro/Configuration.h b/config/examples/Mks/Robin_Pro/Configuration.h index 4da7597bce..9a7d9070d2 100644 --- a/config/examples/Mks/Robin_Pro/Configuration.h +++ b/config/examples/Mks/Robin_Pro/Configuration.h @@ -2070,7 +2070,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2340,13 +2340,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2363,7 +2363,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2371,12 +2371,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Mks/Sbase/Configuration.h b/config/examples/Mks/Sbase/Configuration.h index 2c887fdfd6..289fadf9bd 100644 --- a/config/examples/Mks/Sbase/Configuration.h +++ b/config/examples/Mks/Sbase/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Mks/Sbase/Configuration_adv.h b/config/examples/Mks/Sbase/Configuration_adv.h index d52c884b07..d4a8c52500 100644 --- a/config/examples/Mks/Sbase/Configuration_adv.h +++ b/config/examples/Mks/Sbase/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Modix/Big60/Configuration.h b/config/examples/Modix/Big60/Configuration.h index 90e7c4cb12..2414963aa9 100644 --- a/config/examples/Modix/Big60/Configuration.h +++ b/config/examples/Modix/Big60/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Modix/Big60/Configuration_adv.h b/config/examples/Modix/Big60/Configuration_adv.h index 73844bd61c..cdf41422c0 100644 --- a/config/examples/Modix/Big60/Configuration_adv.h +++ b/config/examples/Modix/Big60/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Ortur 4/Configuration.h b/config/examples/Ortur 4/Configuration.h index 9fe3d899d0..b28663b6bd 100644 --- a/config/examples/Ortur 4/Configuration.h +++ b/config/examples/Ortur 4/Configuration.h @@ -2049,7 +2049,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2319,13 +2319,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2342,7 +2342,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2350,12 +2350,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Ortur 4/Configuration_adv.h b/config/examples/Ortur 4/Configuration_adv.h index 204e60ecb3..34eff070f1 100644 --- a/config/examples/Ortur 4/Configuration_adv.h +++ b/config/examples/Ortur 4/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Printrbot/PrintrboardG2/Configuration.h b/config/examples/Printrbot/PrintrboardG2/Configuration.h index bceb8c50b4..ce91a98252 100644 --- a/config/examples/Printrbot/PrintrboardG2/Configuration.h +++ b/config/examples/Printrbot/PrintrboardG2/Configuration.h @@ -2069,7 +2069,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2339,13 +2339,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2362,7 +2362,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver #define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2375,7 +2375,7 @@ #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) #define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Printrbot/Simple Metal RevD/Configuration.h b/config/examples/Printrbot/Simple Metal RevD/Configuration.h index 64c49f3e02..0e55b5e565 100644 --- a/config/examples/Printrbot/Simple Metal RevD/Configuration.h +++ b/config/examples/Printrbot/Simple Metal RevD/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h b/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h index e7a4032caf..0105cc175b 100644 --- a/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h +++ b/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration.h @@ -2047,7 +2047,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2317,13 +2317,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2340,7 +2340,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2348,12 +2348,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration_adv.h b/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration_adv.h index d4c6894418..806c455118 100644 --- a/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration_adv.h +++ b/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Qidi/Qidi 1/Configuration.h b/config/examples/Qidi/Qidi 1/Configuration.h index df12aecb7f..9ce6c3483b 100644 --- a/config/examples/Qidi/Qidi 1/Configuration.h +++ b/config/examples/Qidi/Qidi 1/Configuration.h @@ -2061,7 +2061,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2331,13 +2331,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2354,7 +2354,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2362,12 +2362,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Qidi/Qidi 1/Configuration_adv.h b/config/examples/Qidi/Qidi 1/Configuration_adv.h index a7f3261b58..f6f552f40b 100644 --- a/config/examples/Qidi/Qidi 1/Configuration_adv.h +++ b/config/examples/Qidi/Qidi 1/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/RapideLite/RL200/Configuration.h b/config/examples/RapideLite/RL200/Configuration.h index c98055df06..f4e607bb11 100644 --- a/config/examples/RapideLite/RL200/Configuration.h +++ b/config/examples/RapideLite/RL200/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/RapideLite/RL200/Configuration_adv.h b/config/examples/RapideLite/RL200/Configuration_adv.h index 447a122796..8571c4fa36 100644 --- a/config/examples/RapideLite/RL200/Configuration_adv.h +++ b/config/examples/RapideLite/RL200/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Renkforce/RF100/Configuration.h b/config/examples/Renkforce/RF100/Configuration.h index e9d2b14ef6..aaf09265a9 100644 --- a/config/examples/Renkforce/RF100/Configuration.h +++ b/config/examples/Renkforce/RF100/Configuration.h @@ -2072,7 +2072,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2342,13 +2342,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2365,7 +2365,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2373,12 +2373,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Renkforce/RF100/Configuration_adv.h b/config/examples/Renkforce/RF100/Configuration_adv.h index 86834c1e68..f0ce8f07f2 100644 --- a/config/examples/Renkforce/RF100/Configuration_adv.h +++ b/config/examples/Renkforce/RF100/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Renkforce/RF100XL/Configuration.h b/config/examples/Renkforce/RF100XL/Configuration.h index 028d09f3e6..ad9fa575be 100644 --- a/config/examples/Renkforce/RF100XL/Configuration.h +++ b/config/examples/Renkforce/RF100XL/Configuration.h @@ -2072,7 +2072,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2342,13 +2342,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2365,7 +2365,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2373,12 +2373,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Renkforce/RF100XL/Configuration_adv.h b/config/examples/Renkforce/RF100XL/Configuration_adv.h index e477972efd..1416754576 100644 --- a/config/examples/Renkforce/RF100XL/Configuration_adv.h +++ b/config/examples/Renkforce/RF100XL/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Renkforce/RF100v2/Configuration.h b/config/examples/Renkforce/RF100v2/Configuration.h index 772db7a342..9a3e30a904 100644 --- a/config/examples/Renkforce/RF100v2/Configuration.h +++ b/config/examples/Renkforce/RF100v2/Configuration.h @@ -2072,7 +2072,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2342,13 +2342,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2365,7 +2365,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2373,12 +2373,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Renkforce/RF100v2/Configuration_adv.h b/config/examples/Renkforce/RF100v2/Configuration_adv.h index e2ae83781c..d6f7ba669d 100644 --- a/config/examples/Renkforce/RF100v2/Configuration_adv.h +++ b/config/examples/Renkforce/RF100v2/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/RepRapPro/Huxley/Configuration.h b/config/examples/RepRapPro/Huxley/Configuration.h index 68612a762e..82287faca5 100644 --- a/config/examples/RepRapPro/Huxley/Configuration.h +++ b/config/examples/RepRapPro/Huxley/Configuration.h @@ -2112,7 +2112,7 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2382,13 +2382,13 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2405,7 +2405,7 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2413,12 +2413,12 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/RepRapWorld/Megatronics/Configuration.h b/config/examples/RepRapWorld/Megatronics/Configuration.h index 68d32ac5a8..46a61ec09f 100644 --- a/config/examples/RepRapWorld/Megatronics/Configuration.h +++ b/config/examples/RepRapWorld/Megatronics/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/RigidBot/Configuration.h b/config/examples/RigidBot/Configuration.h index 51abe47904..6d76a9d918 100644 --- a/config/examples/RigidBot/Configuration.h +++ b/config/examples/RigidBot/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/RigidBot/Configuration_adv.h b/config/examples/RigidBot/Configuration_adv.h index 019a933be3..31d0b2aaa7 100644 --- a/config/examples/RigidBot/Configuration_adv.h +++ b/config/examples/RigidBot/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Robo3D/R1+/Configuration.h b/config/examples/Robo3D/R1+/Configuration.h index 0545d9153a..42de1bbe3f 100644 --- a/config/examples/Robo3D/R1+/Configuration.h +++ b/config/examples/Robo3D/R1+/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/SCARA/MP_SCARA/Configuration.h b/config/examples/SCARA/MP_SCARA/Configuration.h index 70b97e3730..b8348b845f 100644 --- a/config/examples/SCARA/MP_SCARA/Configuration.h +++ b/config/examples/SCARA/MP_SCARA/Configuration.h @@ -2086,7 +2086,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2356,13 +2356,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2379,7 +2379,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2387,12 +2387,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/SCARA/MP_SCARA/Configuration_adv.h b/config/examples/SCARA/MP_SCARA/Configuration_adv.h index 76e21628c8..c37499c388 100644 --- a/config/examples/SCARA/MP_SCARA/Configuration_adv.h +++ b/config/examples/SCARA/MP_SCARA/Configuration_adv.h @@ -487,7 +487,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/SCARA/Morgan/Configuration.h b/config/examples/SCARA/Morgan/Configuration.h index 2924c50dd3..1f86939c63 100644 --- a/config/examples/SCARA/Morgan/Configuration.h +++ b/config/examples/SCARA/Morgan/Configuration.h @@ -2086,7 +2086,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2356,13 +2356,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2379,7 +2379,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2387,12 +2387,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/SCARA/Morgan/Configuration_adv.h b/config/examples/SCARA/Morgan/Configuration_adv.h index 03d6980d32..18a0b5598c 100644 --- a/config/examples/SCARA/Morgan/Configuration_adv.h +++ b/config/examples/SCARA/Morgan/Configuration_adv.h @@ -487,7 +487,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration.h b/config/examples/STM32/Black_STM32F407VET6/Configuration.h index 8164443664..1c1fc5ee24 100644 --- a/config/examples/STM32/Black_STM32F407VET6/Configuration.h +++ b/config/examples/STM32/Black_STM32F407VET6/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h index e17f891866..a4b6ea24a8 100644 --- a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h +++ b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/STM32/STM32F103RE/Configuration.h b/config/examples/STM32/STM32F103RE/Configuration.h index cfb2a17777..b9460779c7 100644 --- a/config/examples/STM32/STM32F103RE/Configuration.h +++ b/config/examples/STM32/STM32F103RE/Configuration.h @@ -2066,7 +2066,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2336,13 +2336,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2359,7 +2359,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2367,12 +2367,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/STM32/STM32F4/Configuration.h b/config/examples/STM32/STM32F4/Configuration.h index 77026fe2a3..8e4bf68162 100644 --- a/config/examples/STM32/STM32F4/Configuration.h +++ b/config/examples/STM32/STM32F4/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Sanguinololu/Configuration.h b/config/examples/Sanguinololu/Configuration.h index 5ee9831b96..724d10c634 100644 --- a/config/examples/Sanguinololu/Configuration.h +++ b/config/examples/Sanguinololu/Configuration.h @@ -2095,7 +2095,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2365,13 +2365,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2388,7 +2388,7 @@ #define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2396,12 +2396,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Sanguinololu/Configuration_adv.h b/config/examples/Sanguinololu/Configuration_adv.h index c9f8ba1c0f..59bfea8ade 100644 --- a/config/examples/Sanguinololu/Configuration_adv.h +++ b/config/examples/Sanguinololu/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Sovol/SV-01/Configuration.h b/config/examples/Sovol/SV-01/Configuration.h index 9e1a68f243..cc8fb52370 100644 --- a/config/examples/Sovol/SV-01/Configuration.h +++ b/config/examples/Sovol/SV-01/Configuration.h @@ -2069,7 +2069,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2339,13 +2339,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2362,7 +2362,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2370,12 +2370,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Sovol/SV-01/Configuration_adv.h b/config/examples/Sovol/SV-01/Configuration_adv.h index a619f60ba1..964c97ad0c 100644 --- a/config/examples/Sovol/SV-01/Configuration_adv.h +++ b/config/examples/Sovol/SV-01/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Tevo/Michelangelo/Configuration.h b/config/examples/Tevo/Michelangelo/Configuration.h index 0bb45c10ea..a91ddb7457 100644 --- a/config/examples/Tevo/Michelangelo/Configuration.h +++ b/config/examples/Tevo/Michelangelo/Configuration.h @@ -2069,7 +2069,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2339,13 +2339,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2362,7 +2362,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2370,12 +2370,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Tevo/Michelangelo/Configuration_adv.h b/config/examples/Tevo/Michelangelo/Configuration_adv.h index c2c1b95092..56021b6862 100644 --- a/config/examples/Tevo/Michelangelo/Configuration_adv.h +++ b/config/examples/Tevo/Michelangelo/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Tevo/Nereus/Configuration.h b/config/examples/Tevo/Nereus/Configuration.h index 6f0d2a4eee..a676e1e715 100644 --- a/config/examples/Tevo/Nereus/Configuration.h +++ b/config/examples/Tevo/Nereus/Configuration.h @@ -2048,7 +2048,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2318,13 +2318,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2341,7 +2341,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2349,12 +2349,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Tevo/Nereus/Configuration_adv.h b/config/examples/Tevo/Nereus/Configuration_adv.h index 7d30be2397..6fa12c959e 100644 --- a/config/examples/Tevo/Nereus/Configuration_adv.h +++ b/config/examples/Tevo/Nereus/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Tevo/Tarantula Pro/Configuration.h b/config/examples/Tevo/Tarantula Pro/Configuration.h index fe12e9306d..57eab30f0c 100644 --- a/config/examples/Tevo/Tarantula Pro/Configuration.h +++ b/config/examples/Tevo/Tarantula Pro/Configuration.h @@ -2069,7 +2069,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2339,13 +2339,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2362,7 +2362,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2370,12 +2370,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Tevo/Tarantula Pro/Configuration_adv.h b/config/examples/Tevo/Tarantula Pro/Configuration_adv.h index 75916ccc51..1c7e11c139 100644 --- a/config/examples/Tevo/Tarantula Pro/Configuration_adv.h +++ b/config/examples/Tevo/Tarantula Pro/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h index 179b6b8a0e..e5005264ce 100644 --- a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h +++ b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h @@ -2069,7 +2069,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2339,13 +2339,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2362,7 +2362,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2370,12 +2370,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h index fb3f6aad4e..9496447bac 100644 --- a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h +++ b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h index 1e7fe86c21..1bf6fdb82b 100644 --- a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h +++ b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h @@ -2072,7 +2072,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2342,13 +2342,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2365,7 +2365,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2373,12 +2373,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h index 7f26ebaca2..a7965f5764 100644 --- a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h +++ b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/TheBorg/Configuration.h b/config/examples/TheBorg/Configuration.h index 99a55eeab9..88ad6ab250 100644 --- a/config/examples/TheBorg/Configuration.h +++ b/config/examples/TheBorg/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/TheBorg/Configuration_adv.h b/config/examples/TheBorg/Configuration_adv.h index b5271ac5f7..9d00bd062a 100644 --- a/config/examples/TheBorg/Configuration_adv.h +++ b/config/examples/TheBorg/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/TinyBoy2/Configuration.h b/config/examples/TinyBoy2/Configuration.h index b187f1021b..2fa51dbda6 100644 --- a/config/examples/TinyBoy2/Configuration.h +++ b/config/examples/TinyBoy2/Configuration.h @@ -2120,7 +2120,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2390,13 +2390,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2413,7 +2413,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2421,12 +2421,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/TinyBoy2/Configuration_adv.h b/config/examples/TinyBoy2/Configuration_adv.h index a53bb27449..e4d6ec96b7 100644 --- a/config/examples/TinyBoy2/Configuration_adv.h +++ b/config/examples/TinyBoy2/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Tronxy/X1/Configuration.h b/config/examples/Tronxy/X1/Configuration.h index 66524590a4..a5828c47ef 100644 --- a/config/examples/Tronxy/X1/Configuration.h +++ b/config/examples/Tronxy/X1/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Tronxy/X3A/Configuration.h b/config/examples/Tronxy/X3A/Configuration.h index 7f7c67f6cd..63357c068e 100644 --- a/config/examples/Tronxy/X3A/Configuration.h +++ b/config/examples/Tronxy/X3A/Configuration.h @@ -2068,7 +2068,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2338,13 +2338,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2361,7 +2361,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2369,12 +2369,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Tronxy/X3A/Configuration_adv.h b/config/examples/Tronxy/X3A/Configuration_adv.h index 52557b1830..40822861f9 100644 --- a/config/examples/Tronxy/X3A/Configuration_adv.h +++ b/config/examples/Tronxy/X3A/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Tronxy/X5S-2E/Configuration.h b/config/examples/Tronxy/X5S-2E/Configuration.h index 8c5da85038..02e8cbe528 100644 --- a/config/examples/Tronxy/X5S-2E/Configuration.h +++ b/config/examples/Tronxy/X5S-2E/Configuration.h @@ -2083,7 +2083,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2353,13 +2353,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2376,7 +2376,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2384,12 +2384,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Tronxy/X5S-2E/Configuration_adv.h b/config/examples/Tronxy/X5S-2E/Configuration_adv.h index b2de699686..175f4fc95a 100644 --- a/config/examples/Tronxy/X5S-2E/Configuration_adv.h +++ b/config/examples/Tronxy/X5S-2E/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Tronxy/X5S/Configuration.h b/config/examples/Tronxy/X5S/Configuration.h index d6b5d2b7ab..a149377ae0 100644 --- a/config/examples/Tronxy/X5S/Configuration.h +++ b/config/examples/Tronxy/X5S/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Tronxy/X5SA/Configuration.h b/config/examples/Tronxy/X5SA/Configuration.h index 3f10bce843..b57e2b2a02 100644 --- a/config/examples/Tronxy/X5SA/Configuration.h +++ b/config/examples/Tronxy/X5SA/Configuration.h @@ -2066,7 +2066,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2346,13 +2346,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2369,7 +2369,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2377,12 +2377,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Tronxy/X5SA/Configuration_adv.h b/config/examples/Tronxy/X5SA/Configuration_adv.h index 6f74f2c1a7..1bfd822267 100644 --- a/config/examples/Tronxy/X5SA/Configuration_adv.h +++ b/config/examples/Tronxy/X5SA/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Tronxy/XY100/Configuration.h b/config/examples/Tronxy/XY100/Configuration.h index 1398d9fe1f..ef3709df78 100644 --- a/config/examples/Tronxy/XY100/Configuration.h +++ b/config/examples/Tronxy/XY100/Configuration.h @@ -2075,7 +2075,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2345,13 +2345,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2368,7 +2368,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2376,12 +2376,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/UltiMachine/Archim1/Configuration.h b/config/examples/UltiMachine/Archim1/Configuration.h index 80d7585952..5608317083 100644 --- a/config/examples/UltiMachine/Archim1/Configuration.h +++ b/config/examples/UltiMachine/Archim1/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/UltiMachine/Archim1/Configuration_adv.h b/config/examples/UltiMachine/Archim1/Configuration_adv.h index caa249e366..64d33dc344 100644 --- a/config/examples/UltiMachine/Archim1/Configuration_adv.h +++ b/config/examples/UltiMachine/Archim1/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/UltiMachine/Archim2/Configuration.h b/config/examples/UltiMachine/Archim2/Configuration.h index c3cb530978..814f2a53dd 100644 --- a/config/examples/UltiMachine/Archim2/Configuration.h +++ b/config/examples/UltiMachine/Archim2/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/UltiMachine/Archim2/Configuration_adv.h b/config/examples/UltiMachine/Archim2/Configuration_adv.h index 37ccd3808b..59e6965a9e 100644 --- a/config/examples/UltiMachine/Archim2/Configuration_adv.h +++ b/config/examples/UltiMachine/Archim2/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/VORONDesign/Configuration.h b/config/examples/VORONDesign/Configuration.h index 0ea28cc652..f5143afdac 100644 --- a/config/examples/VORONDesign/Configuration.h +++ b/config/examples/VORONDesign/Configuration.h @@ -2073,7 +2073,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2343,13 +2343,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2366,7 +2366,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2374,12 +2374,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/VORONDesign/Configuration_adv.h b/config/examples/VORONDesign/Configuration_adv.h index 8589abd8a0..fac7dc6b10 100644 --- a/config/examples/VORONDesign/Configuration_adv.h +++ b/config/examples/VORONDesign/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Velleman/K8200/Configuration.h b/config/examples/Velleman/K8200/Configuration.h index b7c258ae4f..fd66b1eabb 100644 --- a/config/examples/Velleman/K8200/Configuration.h +++ b/config/examples/Velleman/K8200/Configuration.h @@ -2095,7 +2095,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2367,13 +2367,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2390,7 +2390,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2398,12 +2398,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Velleman/K8200/Configuration_adv.h b/config/examples/Velleman/K8200/Configuration_adv.h index cd0bc5c135..ede673c9ef 100644 --- a/config/examples/Velleman/K8200/Configuration_adv.h +++ b/config/examples/Velleman/K8200/Configuration_adv.h @@ -503,7 +503,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Velleman/K8400/Dual-head/Configuration.h b/config/examples/Velleman/K8400/Dual-head/Configuration.h index 1c577dd8bc..16751c3db1 100644 --- a/config/examples/Velleman/K8400/Dual-head/Configuration.h +++ b/config/examples/Velleman/K8400/Dual-head/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2358,7 +2358,7 @@ #define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2366,12 +2366,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h b/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h index 809c831096..b15eb3c6fa 100644 --- a/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h +++ b/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Velleman/K8400/Single-head/Configuration.h b/config/examples/Velleman/K8400/Single-head/Configuration.h index d4fa2260c8..e324790dd8 100644 --- a/config/examples/Velleman/K8400/Single-head/Configuration.h +++ b/config/examples/Velleman/K8400/Single-head/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2358,7 +2358,7 @@ #define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2366,12 +2366,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Velleman/K8400/Single-head/Configuration_adv.h b/config/examples/Velleman/K8400/Single-head/Configuration_adv.h index a5269a6c60..8ea2a68de6 100644 --- a/config/examples/Velleman/K8400/Single-head/Configuration_adv.h +++ b/config/examples/Velleman/K8400/Single-head/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/WASP/PowerWASP/Configuration.h b/config/examples/WASP/PowerWASP/Configuration.h index 075b62eaf0..1082aa6064 100644 --- a/config/examples/WASP/PowerWASP/Configuration.h +++ b/config/examples/WASP/PowerWASP/Configuration.h @@ -2077,7 +2077,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2347,13 +2347,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2370,7 +2370,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2378,12 +2378,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/WASP/PowerWASP/Configuration_adv.h b/config/examples/WASP/PowerWASP/Configuration_adv.h index 15d892d3fc..d268731c77 100644 --- a/config/examples/WASP/PowerWASP/Configuration_adv.h +++ b/config/examples/WASP/PowerWASP/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Wanhao/Duplicator 4S/Configuration.h b/config/examples/Wanhao/Duplicator 4S/Configuration.h index 95e7ef86ce..7d8cba5a68 100644 --- a/config/examples/Wanhao/Duplicator 4S/Configuration.h +++ b/config/examples/Wanhao/Duplicator 4S/Configuration.h @@ -2056,7 +2056,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2326,13 +2326,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2349,7 +2349,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2357,12 +2357,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Wanhao/Duplicator 4S/Configuration_adv.h b/config/examples/Wanhao/Duplicator 4S/Configuration_adv.h index 00e8594e2f..e72299daea 100644 --- a/config/examples/Wanhao/Duplicator 4S/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator 4S/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Wanhao/Duplicator 6/Configuration.h b/config/examples/Wanhao/Duplicator 6/Configuration.h index 22f6da88a6..be879d19db 100644 --- a/config/examples/Wanhao/Duplicator 6/Configuration.h +++ b/config/examples/Wanhao/Duplicator 6/Configuration.h @@ -2074,7 +2074,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2345,13 +2345,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2368,7 +2368,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2376,12 +2376,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h index 1f67cbd7d2..a8a80ecdcb 100644 --- a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm #define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h b/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h index 2878a6c866..5f0c71f1a4 100644 --- a/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h +++ b/config/examples/Wanhao/Duplicator i3 2.1/Configuration.h @@ -2074,7 +2074,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2344,13 +2344,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2367,7 +2367,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2375,12 +2375,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h b/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h index 0ee24d6cd9..0513f48ac6 100644 --- a/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h b/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h index 514fd4c939..391b0f85df 100644 --- a/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h +++ b/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h b/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h index 7734df159e..e294f82267 100644 --- a/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Weistek/wt150/Configuration.h b/config/examples/Weistek/wt150/Configuration.h index e678f32d81..adefd7da95 100644 --- a/config/examples/Weistek/wt150/Configuration.h +++ b/config/examples/Weistek/wt150/Configuration.h @@ -2071,7 +2071,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2341,13 +2341,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2364,7 +2364,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2372,12 +2372,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Weistek/wt150/Configuration_adv.h b/config/examples/Weistek/wt150/Configuration_adv.h index 70fb2e27b2..cbbe5b045b 100644 --- a/config/examples/Weistek/wt150/Configuration_adv.h +++ b/config/examples/Weistek/wt150/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Zonestar/P802M/Configuration.h b/config/examples/Zonestar/P802M/Configuration.h index 8fff0bf06b..1edbc993d6 100644 --- a/config/examples/Zonestar/P802M/Configuration.h +++ b/config/examples/Zonestar/P802M/Configuration.h @@ -2065,7 +2065,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2335,13 +2335,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2358,7 +2358,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2366,12 +2366,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Zonestar/P802M/Configuration_adv.h b/config/examples/Zonestar/P802M/Configuration_adv.h index 4e1e5171b2..fa123c0fe7 100644 --- a/config/examples/Zonestar/P802M/Configuration_adv.h +++ b/config/examples/Zonestar/P802M/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h index e475dadf95..1203a1a7a8 100755 --- a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h +++ b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration.h @@ -2036,7 +2036,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2291,13 +2291,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2314,7 +2314,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2322,12 +2322,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration_adv.h b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration_adv.h index 8f69f5d1d9..316f2bec40 100755 --- a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration_adv.h +++ b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/adafruit/ST7565/Configuration.h b/config/examples/adafruit/ST7565/Configuration.h index e3be09b50b..71eec2a4d6 100644 --- a/config/examples/adafruit/ST7565/Configuration.h +++ b/config/examples/adafruit/ST7565/Configuration.h @@ -2064,7 +2064,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2334,13 +2334,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2357,7 +2357,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2365,12 +2365,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h b/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h index 73c24e3c18..8552cce190 100644 --- a/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h +++ b/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration.h @@ -2236,7 +2236,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2506,13 +2506,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2529,7 +2529,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2537,12 +2537,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration_adv.h b/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration_adv.h index 607342a023..2496d99b07 100644 --- a/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration_adv.h +++ b/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration_adv.h @@ -491,7 +491,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/delta/Anycubic/Kossel/Configuration.h b/config/examples/delta/Anycubic/Kossel/Configuration.h index 6833b78d87..16325a5d5c 100644 --- a/config/examples/delta/Anycubic/Kossel/Configuration.h +++ b/config/examples/delta/Anycubic/Kossel/Configuration.h @@ -2230,7 +2230,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2500,13 +2500,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2523,7 +2523,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2531,12 +2531,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h index afe6fe6925..3f0f7dea02 100644 --- a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h +++ b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/delta/Anycubic/Predator/Configuration.h b/config/examples/delta/Anycubic/Predator/Configuration.h index d27094284d..cfd4699a9c 100644 --- a/config/examples/delta/Anycubic/Predator/Configuration.h +++ b/config/examples/delta/Anycubic/Predator/Configuration.h @@ -2167,7 +2167,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2437,13 +2437,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2460,7 +2460,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2468,12 +2468,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/delta/Anycubic/Predator/Configuration_adv.h b/config/examples/delta/Anycubic/Predator/Configuration_adv.h index beb1d7b9e4..d709067b9f 100644 --- a/config/examples/delta/Anycubic/Predator/Configuration_adv.h +++ b/config/examples/delta/Anycubic/Predator/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/delta/Dreammaker/Overlord/Configuration.h b/config/examples/delta/Dreammaker/Overlord/Configuration.h index 113a89b821..4a778b4390 100644 --- a/config/examples/delta/Dreammaker/Overlord/Configuration.h +++ b/config/examples/delta/Dreammaker/Overlord/Configuration.h @@ -2172,7 +2172,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2442,13 +2442,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2465,7 +2465,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2473,12 +2473,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h b/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h index d6d39b4a7c..1af5f65224 100644 --- a/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h +++ b/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h index e476777152..943cc463c0 100644 --- a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h +++ b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h @@ -2183,7 +2183,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2453,13 +2453,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2476,7 +2476,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2484,12 +2484,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h index 6c9d224239..9720d8dffa 100644 --- a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h +++ b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/delta/FLSUN/QQ-S/Configuration.h b/config/examples/delta/FLSUN/QQ-S/Configuration.h index d566c91bb1..a7c59d8755 100644 --- a/config/examples/delta/FLSUN/QQ-S/Configuration.h +++ b/config/examples/delta/FLSUN/QQ-S/Configuration.h @@ -2174,7 +2174,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2444,13 +2444,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2467,7 +2467,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2475,12 +2475,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h b/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h index 18f56bd9f9..628a075758 100644 --- a/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h +++ b/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h index 5d431d6542..90585ab947 100644 --- a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h +++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h @@ -2176,7 +2176,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2446,13 +2446,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2469,7 +2469,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2477,12 +2477,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h index 2657b8de13..0f6250c25e 100644 --- a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h +++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/delta/FLSUN/kossel/Configuration.h b/config/examples/delta/FLSUN/kossel/Configuration.h index 7fa2f34cbf..bc57fad9fd 100644 --- a/config/examples/delta/FLSUN/kossel/Configuration.h +++ b/config/examples/delta/FLSUN/kossel/Configuration.h @@ -2175,7 +2175,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2445,13 +2445,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2468,7 +2468,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2476,12 +2476,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/delta/FLSUN/kossel/Configuration_adv.h b/config/examples/delta/FLSUN/kossel/Configuration_adv.h index 4e6230e3b1..c4c578f20c 100644 --- a/config/examples/delta/FLSUN/kossel/Configuration_adv.h +++ b/config/examples/delta/FLSUN/kossel/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration.h b/config/examples/delta/FLSUN/kossel_mini/Configuration.h index 183056e5b1..45a62232c6 100644 --- a/config/examples/delta/FLSUN/kossel_mini/Configuration.h +++ b/config/examples/delta/FLSUN/kossel_mini/Configuration.h @@ -2175,7 +2175,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2445,13 +2445,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2468,7 +2468,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2476,12 +2476,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h index 0156526d53..6212b5ae1d 100644 --- a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h +++ b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/delta/Geeetech/G2/Configuration.h b/config/examples/delta/Geeetech/G2/Configuration.h index a23f4de4ce..a9a9db391f 100644 --- a/config/examples/delta/Geeetech/G2/Configuration.h +++ b/config/examples/delta/Geeetech/G2/Configuration.h @@ -2159,7 +2159,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2429,13 +2429,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2452,7 +2452,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2460,12 +2460,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/delta/Geeetech/G2/Configuration_adv.h b/config/examples/delta/Geeetech/G2/Configuration_adv.h index 2e12ddbd75..63c6fd8452 100644 --- a/config/examples/delta/Geeetech/G2/Configuration_adv.h +++ b/config/examples/delta/Geeetech/G2/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/delta/Geeetech/G2Pro/Configuration.h b/config/examples/delta/Geeetech/G2Pro/Configuration.h index 9b7a18d537..6553a56245 100644 --- a/config/examples/delta/Geeetech/G2Pro/Configuration.h +++ b/config/examples/delta/Geeetech/G2Pro/Configuration.h @@ -2159,7 +2159,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2429,13 +2429,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2452,7 +2452,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2460,12 +2460,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/delta/Geeetech/G2Pro/Configuration_adv.h b/config/examples/delta/Geeetech/G2Pro/Configuration_adv.h index 92f3dc891d..509df38965 100644 --- a/config/examples/delta/Geeetech/G2Pro/Configuration_adv.h +++ b/config/examples/delta/Geeetech/G2Pro/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/delta/Geeetech/G2S/Configuration.h b/config/examples/delta/Geeetech/G2S/Configuration.h index ad4b7a6ed0..2268e5f100 100644 --- a/config/examples/delta/Geeetech/G2S/Configuration.h +++ b/config/examples/delta/Geeetech/G2S/Configuration.h @@ -2159,7 +2159,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2429,13 +2429,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2452,7 +2452,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2460,12 +2460,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/delta/Geeetech/G2S/Configuration_adv.h b/config/examples/delta/Geeetech/G2S/Configuration_adv.h index e45a928c01..dd06a5c75b 100644 --- a/config/examples/delta/Geeetech/G2S/Configuration_adv.h +++ b/config/examples/delta/Geeetech/G2S/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/delta/Geeetech/G2SPro/Configuration.h b/config/examples/delta/Geeetech/G2SPro/Configuration.h index 4e621b7c79..b8ebba7eb6 100644 --- a/config/examples/delta/Geeetech/G2SPro/Configuration.h +++ b/config/examples/delta/Geeetech/G2SPro/Configuration.h @@ -2159,7 +2159,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2429,13 +2429,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2452,7 +2452,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2460,12 +2460,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/delta/Geeetech/G2SPro/Configuration_adv.h b/config/examples/delta/Geeetech/G2SPro/Configuration_adv.h index 2eeca53f5b..8eb06302eb 100644 --- a/config/examples/delta/Geeetech/G2SPro/Configuration_adv.h +++ b/config/examples/delta/Geeetech/G2SPro/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration.h b/config/examples/delta/Geeetech/Rostock 301/Configuration.h index ddfeb66977..7df9fb3167 100644 --- a/config/examples/delta/Geeetech/Rostock 301/Configuration.h +++ b/config/examples/delta/Geeetech/Rostock 301/Configuration.h @@ -2164,7 +2164,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2434,13 +2434,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2457,7 +2457,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2465,12 +2465,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h index f4d232aff2..4318d7132e 100644 --- a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h +++ b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/delta/Hatchbox_Alpha/Configuration.h b/config/examples/delta/Hatchbox_Alpha/Configuration.h index bcc18ea087..989f1d17c4 100644 --- a/config/examples/delta/Hatchbox_Alpha/Configuration.h +++ b/config/examples/delta/Hatchbox_Alpha/Configuration.h @@ -2178,7 +2178,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2448,13 +2448,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2471,7 +2471,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2479,12 +2479,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/delta/Hatchbox_Alpha/Configuration_adv.h b/config/examples/delta/Hatchbox_Alpha/Configuration_adv.h index d449b77d0f..36c22dd3b0 100644 --- a/config/examples/delta/Hatchbox_Alpha/Configuration_adv.h +++ b/config/examples/delta/Hatchbox_Alpha/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/delta/MKS/SBASE/Configuration.h b/config/examples/delta/MKS/SBASE/Configuration.h index ef4761662d..969cb3d464 100644 --- a/config/examples/delta/MKS/SBASE/Configuration.h +++ b/config/examples/delta/MKS/SBASE/Configuration.h @@ -2163,7 +2163,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2433,13 +2433,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2456,7 +2456,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2464,12 +2464,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/delta/MKS/SBASE/Configuration_adv.h b/config/examples/delta/MKS/SBASE/Configuration_adv.h index 709672e5c0..d8a25ec9dd 100644 --- a/config/examples/delta/MKS/SBASE/Configuration_adv.h +++ b/config/examples/delta/MKS/SBASE/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/delta/Malyan M300/Configuration.h b/config/examples/delta/Malyan M300/Configuration.h index a656fad388..6d27e82d67 100644 --- a/config/examples/delta/Malyan M300/Configuration.h +++ b/config/examples/delta/Malyan M300/Configuration.h @@ -2134,7 +2134,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2405,13 +2405,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2428,7 +2428,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2436,12 +2436,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/delta/Malyan M300/Configuration_adv.h b/config/examples/delta/Malyan M300/Configuration_adv.h index 09e401a843..cc1040c418 100644 --- a/config/examples/delta/Malyan M300/Configuration_adv.h +++ b/config/examples/delta/Malyan M300/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/delta/Tevo Little Monster/Configuration.h b/config/examples/delta/Tevo Little Monster/Configuration.h index f9c2e317ad..53936cce4a 100644 --- a/config/examples/delta/Tevo Little Monster/Configuration.h +++ b/config/examples/delta/Tevo Little Monster/Configuration.h @@ -2167,7 +2167,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2437,13 +2437,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2460,7 +2460,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2468,12 +2468,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/delta/Tevo Little Monster/Configuration_adv.h b/config/examples/delta/Tevo Little Monster/Configuration_adv.h index 59baf68351..7f1d638840 100644 --- a/config/examples/delta/Tevo Little Monster/Configuration_adv.h +++ b/config/examples/delta/Tevo Little Monster/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/delta/generic/Configuration.h b/config/examples/delta/generic/Configuration.h index 5663fd8fe3..22264d8546 100644 --- a/config/examples/delta/generic/Configuration.h +++ b/config/examples/delta/generic/Configuration.h @@ -2163,7 +2163,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2433,13 +2433,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2456,7 +2456,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2464,12 +2464,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/delta/generic/Configuration_adv.h b/config/examples/delta/generic/Configuration_adv.h index e1d0309dcf..71e1b50f1f 100644 --- a/config/examples/delta/generic/Configuration_adv.h +++ b/config/examples/delta/generic/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/delta/kossel_clear/Configuration.h b/config/examples/delta/kossel_clear/Configuration.h index ee8eef2730..7c2dfd621c 100644 --- a/config/examples/delta/kossel_clear/Configuration.h +++ b/config/examples/delta/kossel_clear/Configuration.h @@ -2157,7 +2157,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2427,13 +2427,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2450,7 +2450,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2458,12 +2458,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/delta/kossel_clear/Configuration_adv.h b/config/examples/delta/kossel_clear/Configuration_adv.h index 7ba2549600..c57498f61e 100644 --- a/config/examples/delta/kossel_clear/Configuration_adv.h +++ b/config/examples/delta/kossel_clear/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/delta/kossel_mini/Configuration.h b/config/examples/delta/kossel_mini/Configuration.h index a252d0a1fe..f39ce44589 100644 --- a/config/examples/delta/kossel_mini/Configuration.h +++ b/config/examples/delta/kossel_mini/Configuration.h @@ -2165,7 +2165,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2435,13 +2435,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2458,7 +2458,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2466,12 +2466,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/delta/kossel_mini/Configuration_adv.h b/config/examples/delta/kossel_mini/Configuration_adv.h index af1af00908..41a2518433 100644 --- a/config/examples/delta/kossel_mini/Configuration_adv.h +++ b/config/examples/delta/kossel_mini/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/delta/kossel_pro/Configuration.h b/config/examples/delta/kossel_pro/Configuration.h index 13a71e65e1..7166d1ae27 100644 --- a/config/examples/delta/kossel_pro/Configuration.h +++ b/config/examples/delta/kossel_pro/Configuration.h @@ -2165,7 +2165,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2435,13 +2435,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2458,7 +2458,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2466,12 +2466,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/delta/kossel_xl/Configuration.h b/config/examples/delta/kossel_xl/Configuration.h index eed1ee8da1..e19490d8ae 100644 --- a/config/examples/delta/kossel_xl/Configuration.h +++ b/config/examples/delta/kossel_xl/Configuration.h @@ -2166,7 +2166,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2436,13 +2436,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2459,7 +2459,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2467,12 +2467,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/delta/kossel_xl/Configuration_adv.h b/config/examples/delta/kossel_xl/Configuration_adv.h index 07dab4fd2c..f9aa551de4 100644 --- a/config/examples/delta/kossel_xl/Configuration_adv.h +++ b/config/examples/delta/kossel_xl/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/gCreate/gMax1.5+/Configuration.h b/config/examples/gCreate/gMax1.5+/Configuration.h index 05b9e1d8ef..cb48e82723 100644 --- a/config/examples/gCreate/gMax1.5+/Configuration.h +++ b/config/examples/gCreate/gMax1.5+/Configuration.h @@ -2076,7 +2076,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2346,13 +2346,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2369,7 +2369,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2377,12 +2377,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/gCreate/gMax1.5+/Configuration_adv.h b/config/examples/gCreate/gMax1.5+/Configuration_adv.h index ce78dbeb3e..86aeca6ea3 100644 --- a/config/examples/gCreate/gMax1.5+/Configuration_adv.h +++ b/config/examples/gCreate/gMax1.5+/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/makibox/Configuration.h b/config/examples/makibox/Configuration.h index 184cd7614f..8ca7f3eebb 100644 --- a/config/examples/makibox/Configuration.h +++ b/config/examples/makibox/Configuration.h @@ -2067,7 +2067,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2337,13 +2337,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2360,7 +2360,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2368,12 +2368,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/makibox/Configuration_adv.h b/config/examples/makibox/Configuration_adv.h index b26d31bd69..6e8f868e47 100644 --- a/config/examples/makibox/Configuration_adv.h +++ b/config/examples/makibox/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif diff --git a/config/examples/tvrrug/Round2/Configuration.h b/config/examples/tvrrug/Round2/Configuration.h index fca743e391..99df69312a 100644 --- a/config/examples/tvrrug/Round2/Configuration.h +++ b/config/examples/tvrrug/Round2/Configuration.h @@ -2059,7 +2059,7 @@ //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) //#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight -//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. NeoPixel RGB Backlight //#define FYSETC_GENERIC_12864_1_1 // Larger display with basic ON/OFF backlight. // @@ -2329,13 +2329,13 @@ * Adds the M150 command to set the LED (or LED strip) color. * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * luminance values can be set from 0 to 255. - * For Neopixel LED an overall brightness parameter is also available. + * For NeoPixel LED an overall brightness parameter is also available. * * *** CAUTION *** * LED Strips require a MOSFET Chip between PWM lines and LEDs, * as the Arduino cannot handle the current the LEDs will require. * Failure to follow this precaution can destroy your Arduino! - * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * NOTE: A separate 5V power supply is required! The NeoPixel LED needs * more current than the Arduino 5V linear regulator can produce. * *** CAUTION *** * @@ -2352,7 +2352,7 @@ //#define RGB_LED_W_PIN -1 #endif -// Support for Adafruit Neopixel LED driver +// Support for Adafruit NeoPixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) @@ -2360,12 +2360,12 @@ //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 //#define NEOPIXEL2_INSERIES // Default behavior is NeoPixel 2 in parallel - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 NeoPixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup - // Use a single Neopixel LED for static (background) lighting + // Use a single NeoPixel LED for static (background) lighting //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W #endif diff --git a/config/examples/tvrrug/Round2/Configuration_adv.h b/config/examples/tvrrug/Round2/Configuration_adv.h index 3f8d7c220a..3379a2a182 100644 --- a/config/examples/tvrrug/Round2/Configuration_adv.h +++ b/config/examples/tvrrug/Round2/Configuration_adv.h @@ -490,7 +490,7 @@ //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. - //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + //#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif